Forum Post: RE: ADS1262: Noise issue
Hi Naoki-san, Sorry for the delayed response. We had a server issue earlier this week and I was not notified of your first post. Thanks for following up. According to the noise plots the first test...
View ArticleForum Post: RE: ADS1262: Noise issue
Hello Chris, Thank you for your reply. I see, I will send you the information using a private message. I explain the waveform in the attached file. Page2: It is a input signal. Measure at the front of...
View ArticleForum Post: RE: ADS1257: Setup ADS1257 Concerns
Hi Khoi, Setting up an MCU's SPI peripheral shouldn't be an entirely manual process if you are working with an SPI peripheral. Yes there are some timing requirement that you need to pay attention to...
View ArticleForum Post: RE: AFE4300EVM-PDK: Device GUI
Hi, To use the GUI with your own board, you have to program your MCU's firmware such that it understands and react to the commands sent by the GUI. So here the bottleneck is MCU not the AFE. Regards,...
View ArticleForum Post: RE: Design Low cost Weighing Scale
Hi Bob B, thanks for your clarification and i request to sample ads1230 and 1130, after getting this i will connect with CC3220 evaluation board. so can you please update any example for my project...
View ArticleForum Post: RE: AFE4405EVM: The eval board stopped working. Software issue
Hi Mats, Does the EVM gets detected properly by the PC? Can you please share the screenshot of your device manager with the EVM connected? Regards, Prabin.
View ArticleForum Post: ADS1274: ADS1274 effective input impedance
Part Number: ADS1274 Hi, In my application I'm using the ADS1274 , 24- BIT Analog to Digital Converter. Due to limited PCB space, I'm thinking of giving up the pre amplifiers that drives the input...
View ArticleForum Post: RE: TINA / Spice / DAC0800: Spice model for legacy devices
hi,Kevin Thanks for answer,i understand need time for create SPICE model,my wish achieved success in that work
View ArticleForum Post: DAC37J82: Why four analog outputs?
Part Number: DAC37J82 Hi, I'm looking for ~1GSPS DAC with two analog outputs. DAC37J82 is listed as "dual" and indeed has two digital paths, but four muxed analog outputs. Why is that? Is it some reuse...
View ArticleForum Post: RE: TINA/Spice/ADS1298: ADS1298
Dear Alex, I thank you very much for your continuous support. I have already changed the WCT register to D4h. However nothing is changed. My register values are as follows: // Boot sequence // Issue...
View ArticleForum Post: RE: AFE4405EVM: The eval board stopped working. Software issue
Hi Prabi, yes it seem so. As written before, I can upload a new firmware to the EVM via the exe-program without GUI. Regarding screenshot; See attached file. BR/Mats
View ArticleForum Post: ADS8887: software driver
Part Number: ADS8887 HI , Is there a software SPI driver for this part !? Thanks.
View ArticleForum Post: ltm8064 heating issue
I am using LTM8064 for converting input voltage in the range of 24-50 V to 24 V, 8A by connecting 2 chips in parallel. Will this cause a heating issue to my pcb? I am confused whether I should procure...
View ArticleForum Post: ADS1247: Input range vs output data : abnormal phenomenon
Part Number: ADS1247 Hi, I would like to ask you to give me your idea about following phenomenon. My customer has observed abnormal phenomenon about output data when input is out of "Vref". That is to...
View ArticleForum Post: RE: DAC8718: DAC8718 Smaple code
Hi, Thank you for your query. We don't have any specific example for DAC8718 . However, you can look at this third-party article on how to interface to DAC8734EVM . These parts are similar:...
View ArticleForum Post: AFE4490: AFE_RESET pin
Part Number: AFE4490 Hi all, In the circuit given below pin number 29 (RESETZ) is pulled up to vcc and same time it is connected to the port pin of a microcontroller,how this set up work ,what is the...
View ArticleForum Post: RE: ADS54J60EVM: Shifting the phase of the ADC clock in very...
Good morning Jim, Yesterday evening I soldered a 16 GHz high impedance probe to the termination resistor R32 (the solder point is on the capacitors C65 and C73 which connect to R32) as shown on the...
View ArticleForum Post: RE: DAC121S101: DAC121S101
Hello Mr Duke, Thank you very much for your answer. I have a second question about the radiation resistance (SEE, SET, dose) of component DAC121S101 / Q1. Would you have radiation data for this same...
View ArticleForum Post: RE: ADS54J60EVM: Shifting the phase of the ADC clock in very...
Jim, I updated my log "Dec 5, 2018 3:13 PM" with the config files... looks like the attachment only looks odd when editing, but later on the webpage is is correctly inserted as files. Cheers Goran
View Article