Forum Post: RE: AFE5809EVM ON BOARD CLOCK @ 8MHz in CW mode?
Hi Enrico,please find the answer below:-1. Can we have the output I / Q (on J12 / J13) of a single channel (only J1 for example) instead of all mixed together?No you can't. Using more channels at the...
View ArticleForum Post: RE: minimum voltage/power to VPF (8,53 pin) and VNF (10,51 pin )...
Hi Samir,Just put between VPP/VPF and VNN/VNF 470nF/100V capacitors. Nothing else you should do.Best Regards,Mariusz
View ArticleForum Post: RE: Need Help for Ultrasonic Imaging Applications of...
Hi Shiwei,Q1: The TOD variance on various LM96570 chips could be up to 15.5ns and it's unknown and unpredictible. It's ABSOLUTELY unusable in >8 channel applications. Not worth a single penny.Best...
View ArticleForum Post: How to use CCSv5.2 for showing a existing image
For instance, if there is a image named 01.bmp , how can I use the CCSV5.2 to read it and show it?Thanks for your attention to this matter.
View ArticleForum Post: Survey data driver with high impedance state
Hi,Could you suggest me a IC which has 3 states including On state (about 5V), Off state (0V), and High Impedance state(floating) ?I would like to build a system which can output 5V , 0V, or being...
View ArticleForum Post: LM98714
Dear, Sir. I would like to make sure several things regarding LM98714.Typical application is configured by CCD like image sensor, LM98714, LVDS Rx and ASIC. SH_R provides from ASIC, then CCD starts to...
View ArticleForum Post: Info AFE LM98519
I would usetheLM98519AFEwith sensorSony linear CCD ILX585K, but the datasheetdoes not mentionprogramming theSPIto program/command, butonlythe block diagram. Wherecan I find information?
View ArticleForum Post: RE: Damaged AFE5808 in Evaluation Module
Luis,That power consumption is correct. Is this why you think the AFE is broken? There is no special heat sink for the board and the holes are designed for a socket and not a fan.Thanks,Chuck Smyth
View ArticleForum Post: RE: help in AFE5808 clocking
Dear Chandu,the AFE5808 can accept both differential and single ended clocks both in CW and TGC mode and as per datasheet it doesn't seem to make any difference in terms of performances. With that...
View ArticleForum Post: RE: Damaged AFE5808 in Evaluation Module
Chuck It doesn't work anymore, tt doesn't respond to any command sent by GUI software.ThanksLuis Zavala
View ArticleForum Post: RE: Info AFE LM98519
Hello,The information you are looking for is within the full datasheet which can be disclosed if there is NDA in place. Please let me know and I can send the full datasheet once the paperwork is in...
View ArticleForum Post: RE: Does LM96511EVK include a WAVEVISION5 CAPTURE BOARD ?
Dear PeymanThank you for your kind reply.I also send this information to the customer.This projedt is a brandnew ,so they are interested about it.Best regards,Shinichi Inoue
View ArticleForum Post: RE: AFE5809 VCAT response time by SPI configure including the SPI...
Hi Winston,please find below the answer.The data for this are not readily available and are not in the datasheet. If this is a critical spec, we can dig deeper and make this measurement. Please let...
View ArticleForum Post: RE: Damaged AFE5808 in Evaluation Module
Hi Chuck,I do also own an AFE5808A_EVM and I'd like to place a heatsink on the AFE as well but I don't find any standard solution, could you provide me any reference?About the holes present in the EVM,...
View ArticleClik here to view.
Forum Post: doubt in datasheet of LM96570
Hi,I have some doubts in using the LM96570 IC. 1) In data sheet of LM96570 are mentioned as default values, so shall I assume those are the values of registers when powered up before programming...
View ArticleForum Post: got damage at pulser IC in Tx_sdk_v1
Hi, When I connected the complete setup of TX_sdk_v1 to PC, led was on in opall kelly board but DOTP1 led in Trasmit solution board was off. Is it indicates any problem in board. And then I...
View ArticleForum Post: RE: Damaged AFE5808 in Evaluation Module
Hi, Same problem I also got, if I replace with new afe5808 the GUI can access it ?thank you.regards,chandu
View ArticleForum Post: RE: got damage at pulser IC in Tx_sdk_v1
Hi Chandu,When powering on properly, the DOTP1 LED should be on. Before powering up, do you have the jumper J_SUB connect properly? If you are using 2 power supplies for VSUB & VNN, then you need...
View ArticleForum Post: RE: Damaged AFE5808 in Evaluation Module
Chandu,I don't understand your question. Are you having a power supply short with excessive current?Thanks,Chuck Smyth
View ArticleForum Post: RE: need help on 16 channel US pulser
Hi Can any one help me ,how to give +/- 50V to TX_SDK_V1?can i use DC +/-50V supply or should i use regulated supply?Is there any separate power supply modules for TX_SDK_V1?Recently i have given -50V...
View Article