Forum Post: RE: AMC7812: seeking support for I2C communication in AMC7812
(Please visit the site to view this file)
View ArticleForum Post: RE: AMC7812: seeking support for I2C communication in AMC7812
I had used the SDA and SCL connection for I2C ; A0, A1and A2 for slave selection and reset pin is given high.
View ArticleForum Post: Linux/AFE4405: AFE4405
Part Number: AFE4405 Tool/software: Linux Dear TI team, I wrote an e-mail to mysecuresoftware_medical@list.ti.com for AFE4405 full datasheet , but i didn't get answer. Have you any idea how can i get?
View ArticleForum Post: RE: ADS8920B: Replacing a Microchip MCP3550 ADC with an ADS8920B
Hi Keith, Thanks so much for all the consultation. I'm just trying to interpret the enhanced SPI requirements- it seems most of them utilize other digital lines. If we go with the 4 wire (/CS, SCLK,...
View ArticleForum Post: RE: AFE5809: Demodulator's DVDD_LDO1/2 sepcification questions
Hi Chen, that is just what I am planning to do. Thanks.
View ArticleForum Post: RE: DAC38RF82: DAC38RF82 RX[0..7] input channnel electrical...
hello,Jim If we could select the DAC B output when DAC38RF82 is working in only one DAC mode ?
View ArticleForum Post: RE: AFE4400: Artifacts in SPO2
Artifacts- Movement of hands, fingers. I think it is due to motion. We have interfaced AFE4400 to MSP430F5529 and CC3200Mod only. if there is movement of finger - there is a lot of difference in the...
View ArticleForum Post: ADC12DJ3200EVM: Cannot connect the GUI software anymore
Part Number: ADC12DJ3200EVM Hi, I have the ADC12DJ3200EVM Rev A eval board and I have been using it for quite some time now with TSW14J57. I am not sure what happened but now the GUI software doesnt...
View ArticleForum Post: RE: ADS1256: Setting up the SPI Logic Analyzer for ADS1256
Hi Chris, I tried your suggestion and I think there is something going on with the oscilloscope results drive.google.com/open yellow is the clock, it works normally Green is the MISO line, it doesn't...
View ArticleForum Post: RE: ADC12DJ3200EVM: Cannot connect the GUI software anymore
Now i am getting this after i uninstalled and reinstalled. I installed 2014 and 2018 labview runtime but it still gives me this.
View ArticleForum Post: RE: ADS1299: AC Lead Off / Impedance Measurement
Good, I have checked but where seem to be some contradictions about this, mostly with the single electrode measurement possibility, with internal current source. Most EEG discussions talk about...
View ArticleForum Post: What is the ADC converter to be used with BeagleBoard-X15 to...
Hi, i want to measure temperature in order to control heater. I have three compartiments in my machines where i want to control heater. i have three PT100 temperature sensor with output: 0-10V The...
View ArticleForum Post: ADS1298R: Wiring respiration leads
Part Number: ADS1298R Hello! Section 9.3.1.7.8.2 of ADS1298R datasheet describes: When this respiration option is enabled, ADS129xR channel 1 cannot be used to acquire ECG signals. If the RA and LA...
View ArticleForum Post: RE: ADS7039-Q1: SPI timing, 16 SCK pulses input
Thank you vey much Joseph I will study how to do with this with my SoC. Ryuji Saito
View ArticleForum Post: RE: ADS8920B: Replacing a Microchip MCP3550 ADC with an ADS8920B
Hi Ian, Using Zone 2 for reading 16b conversion data will require 18MHz SCLK speed using only 4 wires. If you want to read the parity bits, the clock speed will be slightly higher, ~20MHz. Hope this...
View ArticleForum Post: RE: ADS1204: Influence of the Input Source Impedance
Hi Nicole, Are you able to test your system with and without a buffer on the input to the ADS1204 ?
View ArticleForum Post: ADS1299EEGFE-PDK: No output from the Dout pin of the evaluation...
Part Number: ADS1299EEGFE-PDK Greetings. I am trying to interface ADS1299EEGFE-PDK with Arduino for acquisition of EEG signals. I am using the library given in the link given below...
View ArticleForum Post: RE: What is the ADC converter to be used with BeagleBoard-X15 to...
Hi, 1. Yes, the device should be able to work with three sensors at once, if they are connected to different interface instances. 2. There is no particular recommendation for this. Basically AM5728...
View ArticleForum Post: TSW1400EVM: No firmware error
Part Number: TSW1400EVM I`m trying to connect TSW1400EVM to AFE5832EVA. I downloaded HSDC v5.0, but there is no firmware for AFE5832 in Select ADC. Also, I can`t find AFE5832 GUI program. Other model`s...
View ArticleForum Post: RE: ADS8920B: Replacing a Microchip MCP3550 ADC with an ADS8920B
Hi Keith, I see what you're saying... but when you say 4 wires, is the 4th wire connected to SDI? From the datasheet I thought enhanced SPI required the use of a different pin such as CONVST. Thanks...
View Article