Forum Post: RE: ADS5263: Must the signal input to 4 input pins for operating...
Hi chen, Thank you for your sincere answer. I understood about your answer as atached. Is this picture what you are saying for single input? Thank you Best regards, Jaden
View ArticleForum Post: RE: ADS5562: ADS5562 16bit ADC analog input & ADC convert formula
Hi Neeraj, Thank a lot for your reply, where can find the datasheet as picture 2? Base on picture 2, so we can get worset reolsution(volt per bit) is, 3.56/power(2,16-1)? If Vpp = 3.56, it means that...
View ArticleForum Post: RE: ADS1118EVM: Urgent: DOUT not responding to CS pin as expected
Hi, I have a board with a nRF52840 driving the ADS1018 . This one work fine now, I had some gpio issues. But when I tried to debug and tunderstand ADS1018 behavior, I used ADS1118EVM + USB_DIG. On this...
View ArticleForum Post: RE: ADS8028EVM-PDK: External Microcontroller
Hi Joseph, Thanks for the answer! Regards, Jianxiong
View ArticleForum Post: ADS1248: ADS1248 output error
Part Number: ADS1248 Dear Sir, My customer is testing ADS1248 using R6161 DC voltage generator to supply. The generator supplies 0mV to ADC input through INA129 , then monitor ADC digital output. An...
View ArticleForum Post: RE: ADS8350EVM-PDK: ADS8350EVM-PDK software problem
Hi Ryan, Yes I'm the administrator for both PCs. I hope that Sandeep can find the issue. Best regards, Merlin
View ArticleForum Post: RE: ADS122U04: ADS122U04 Failing Miserably!
Thank you, Bob, for the insights. Could you please elaborate how there could be any leakage paths around the ~RESET pin in the concerned PCB? As far as flux residue is concerned, we make sure to...
View ArticleForum Post: ADC32RF45EVM: Mechanical model and layout files
Part Number: ADC32RF45EVM Hello, We're intending to interface this board with our in house FPGA board. To do this we need 3D (STEP ) model of the EVM. The actual layout file (.brd), can be used both...
View ArticleForum Post: ADS54J66: ADS54J66
Part Number: ADS54J66 Hi, We manufacture a board according ADS54j66EVM , and test it with TSW14J56. We configure ADS54j66 to mode 8 using ADS54JXX EVM. We find that when we set DCLK(to ADC) to...
View ArticleForum Post: ADS7953: CS PIN SWITCHING
Part Number: ADS7953 HI, from datasheet i checked that CS pin has to be switch for each frame in any mode to get data, but what will happen if i make CS pin low for first time and then keep it low and...
View ArticleForum Post: ADS1299EEGFE-PDK: 50 hz interference
Part Number: ADS1299EEGFE-PDK Hi, I am trying acquire the EEG signals from a real patient using ADS1299 EEGFE-PDK. I have placed 1 electrode on the forehead and another on the earlobe as reference. I...
View ArticleForum Post: TLC7226: The four ouputs change from operating voltage to 0V...
Part Number: TLC7226 The TLC7226C outputs connect to max301 directly. Sometimes the four outputs change from operating voltage to 0V . I can confirm that Mcu do not control it. What happened will the...
View ArticleForum Post: RE: Linux/TSC2007: Regarding Device tree configuration on Android.
Dear Sir, Please provide header file related to 1108. tsc2007 .c file, when i compile this code with i got error. Thanks and regards,
View ArticleForum Post: RE: ADS1292: Using the ADS1292 without RLD electrode
Hello Ryan, Thanks for your answer. I am not sure if I completely understand. Maybe I can be a little bit more specific. Lets suppose a battery powered device because this would make the most sense not...
View ArticleForum Post: RE: ADS8588S: Use one channel for data correction and fault...
Hi Dale, Noted with thanks.
View ArticleForum Post: RE: ADS7953: CS PIN SWITCHING
Hi Joseph, Thank for your quick reply, i am using TMS320F28379D controller , i want to read all 16 channels in auto1 mode so i used FIFO mode and pushed all 16 words. in this case CS pin is low for all...
View ArticleForum Post: RE: DAC8571: DAC for music audio
Duke, Thank you for your reply. I am honestly not too familiar on the differences an audio DAC would bring, but if you have some examples I would love to look into this solution. My performance...
View ArticleForum Post: DAC3482: SYNC configuration
Part Number: DAC3482 Hi team, My customer used DAC3482 and LMK04803 , having some questions need your kind help: 1. Can SYNC be connected to FPGA? 2. Does FRAME and SYNC have FIFO function? Can SYNC be...
View ArticleForum Post: RE: ADS1298: Not able to write registers of ADS1298 with...
Hello, thanks for reply, i have tied the CS Pin to low as of now to get initialize and to fist communication done. Also, I want to let you know that i my DRDY pin is not going high to low after giving...
View Article