Forum Post: ADS1232: Hi people I am new for adc , I have 10mV signal from my...
Part Number: ADS1232 Hi people I am new for adc , I have 10mV signal from my senor and this signal is sent through the normal pcb track to the adc. Can ads1232 detect and process the signal ?,Is there...
View ArticleForum Post: RE: DAC3482: How do I recognize PLL as locked? "pll_lfvolt" stays...
Hi Shim, There are many possibilities. You will first need to check if your configuration is correct or not. The next thing is to check if any of the alarms are triggered. We can determine more. it is...
View ArticleForum Post: ADS131E08EVM-PDK: ENOB calculation
Part Number: ADS131E08EVM-PDK Hi Team, We want to calculate or check the ENOB for ADS131E08 EVM-PDK kit. For particular PGA Gain and Data rate we will have certain ENOB as mentioned in Table 1(Pg. no...
View ArticleForum Post: RE: ADS7057EVM-PDK: External source for Single to Differential
Hello Keith, Thank you for your suggestion. More question about this test environment. 1.Could you share what kind of Single - ended source would you recommend or TI use ? I've tried some source and...
View ArticleForum Post: AFE5401-Q1: Trigger to DSYNC2 latency and digital output latency
Part Number: AFE5401-Q1 Hello, I am using the AFE5401-Q1 and I have a few questions regarding the devices Trigger to DSYNC2 latency and digital output latency. This was the test setup for the first...
View ArticleForum Post: DAC8742HEVM: Can I use some teraterm terminal to read DAC8742HEVM...
Part Number: DAC8742HEVM Can I use some teraterm terminal to read DAC8742HEVM HART by UART interface? Is there any instruction to access DAC8742HEVM UART interface from PC Serial port by Putty(terminal...
View ArticleForum Post: RE: ADS1224: IBIS Model behavior
Hi Bob-san, Thank you for your reply. The detail is included a confidential information for the customer. So, I sent by private message. Could you confirm it? Best Regards, Koji Hamamoto
View ArticleForum Post: ADS1261: Full Scale Calibration
Part Number: ADS1261 Dear Technical Support Team, ①Is it ok to execute only GANCAL for Full-Scale Calibration automatically? 　Output code is over 7FFFFFh while applying full-scale Vin(for example,...
View ArticleForum Post: RE: DAC7760: Proper output is not coming for the input DAC code
Hi Garrett, Thank You for your response. For your reference I have attached waveforms of SPI communication once again with correct voltage levels. 1. Reset register with value 0x560001 2.Configuration...
View ArticleForum Post: DDC264EVM: Are the design files available?
Part Number: DDC264EVM Hi Do you have the original schematic (OrCAD) and PCB source files available for this board? Many thanks Steve
View ArticleForum Post: RE: TINA/Spice/ADS1018-Q1: ADS1018-Q1
Hi Joseph, Thank you very much. It is really a great information. Only one doubt. I understood errors due to filters. However how Rpu and Rpd can incorporate errors as if both are equal and drift...
View ArticleForum Post: RE: ADC12D1600: Data from the ADC is not correct.
Hi Nikola Have you made any progress on this issue? Can you provide the information I requested in my previous post, so I can replicate your setup and provide data captured from the ADC outputs using a...
View ArticleForum Post: RE: DDC232: Which Microcontroller for DDC232
Could you help me elaborate what it means by 'pC'? Based on your comparisons, there are not much differences between 264 and 1128 besides the NDA and the number of channels. As for prototyping, I would...
View ArticleForum Post: RE: ADS1232: Hi people I am new for adc , I have 10mV signal from...
Can you please help me to choose the filter, i don't know how to calculate the filter value(RC) and what are all the parameter i consider while calculating the filter .can you attach the formula and...
View ArticleForum Post: ADS7057EVM-PDK: Recommend signal source for Spectral Analyse ?
Part Number: ADS7057EVM-PDK Hello, I have some question about ADS7057EVM-PDK , 1.May I know what kind of Single - ended source would you recommend or TI use ? I've tried some source and till now get...
View ArticleForum Post: RE: DAC8742HEVM: Can I use some teraterm terminal to read...
Hi Garrett, Very thankful of your information. I don't use EVM software because I would like to read HART transmitter data from "COMMAND 3" to get PV, SV, TV, QV by Raspberry Pi UART /ttyAMA0...
View ArticleForum Post: ADS8688: tidu365b design -18V needed or not
Part Number: ADS8688 HI All I see tidu365b schematic. I don't know why R74 connect to -18V_ISO not SGND?
View ArticleForum Post: TSW1405EVM: TSW1405EVM
Part Number: TSW1405EVM I am trying to use 1405 with AFE5809 . I assume * .ini file is missing in the high speed data convertor app under 1405 detail directory. Can you please provide the ini file...
View ArticleForum Post: DAC7311: Output rail issue
Part Number: DAC7311 Hi, Our customer evaluated the DAC7311 , but the output rail was Vs-0.6V. The circuit and data are below. 1) Are there any problems with the circuit? 2) When the load of the DAC is...
View Article