Forum Post: RE: LM96550
Dear Yuan! Where could you find the LM96550 , 96570, 96530, etc. schematic models for Eagle (or Orcad Pspice)? I tried to find them for designing and simulation, but i could not find. Please help me....
View ArticleForum Post: RE: LM98620 eval board schematic
Hello Hooman, Any good news? I really in need for the EVM Gerber files or the source schematics, so please if it possible share them. Regards
View ArticleForum Post: RE: LM98620 eval board schematic
Hi Mohammed, I'm currently not in my office. I'll get back on Wednesday and I'll look to get you the gerber files you've asked for. Regards, Hooman
View ArticleForum Post: LM98714: What's difference between LM98714BCMT and LM98714CCMT?
Part Number: LM98714 Hi, Could you kindly advise me what's different LM98714 BCMT from LM98714 CCMT ? Thanks.
View ArticleForum Post: RE: LM98714: What's difference between LM98714BCMT and LM98714CCMT?
Hello James, I am moving your post to the Imaging AFEs forum where the device LM98714 is supported.
View ArticleForum Post: RE: LM98620 eval board schematic
Hi Mohammed, I've uploaded whatever I had on this EVM that resembles Gerber files in the original location zip file: 3580.0131.LM98620 EVM.zip Hopefully this is what you are looking for? Sorry, I don't...
View ArticleForum Post: RE: LM98714 Initialization code
Hi Hooman, I have difficulty understanding the values of registers PIX1 Start, PIX1 End, PIX2 Start, PIX2 End, PIX3 Start, PIX3 End, PIX4 Start, PIX4 End (Page 2 address 0x7 through 0x11). What is the...
View ArticleForum Post: LM9833: Compatibility with FR12F-J03 Canon contact image sensor...
Part Number: LM9833 Hi, While looking through the datasheet of the LM9833 , it says that it is "compatible with a wide range of color linear CCDs and Contact Image Sensors (CIS)." However, the...
View ArticleForum Post: RE: LM98714 Initialization code
Hi Prasanna, Sorry about the delay in getting back to you. Question : What is the reference for start/end? ADC clock or Pixel clock or something else. Response : The reference point for Start and End...
View ArticleForum Post: RE: LM9833: Compatibility with FR12F-J03 Canon contact image...
Hi Eurah, I am moving your post to the Imaging AFE forum where the device LM9833 is supported.
View ArticleForum Post: RE: LM9833: Compatibility with FR12F-J03 Canon contact image...
Hi Eurah The LM9833 could work with that sensor. Key parameters to consider are the necessary sample rate (4 MHz) and the ability to capture CIS waveforms with pixel counts up to 10296. The LM9833 can...
View ArticleForum Post: RE: LM98714 Initialization code
Thanks Hooman. I am able to generate the clock pulses as per my sensor timing. Regards Prasanna
View ArticleForum Post: RE: Using LM98725
Hello Hooman, I would like to thank for your support in configuring the LM98725 chip for our experimental project. Finally I have got some result but its not that good in the attachment you can see it....
View ArticleForum Post: RE: Using LM98725
Hi Martin, Glad to hear that things have improved! The DAC and PGA register settings for each channel (Red, Green, Blue) should be adjusted for the following goals. Adjust DAC values until the average...
View ArticleForum Post: RE: Using LM98725
Hello Hooman, By full scale value you mean the max. value at 16 bit data i.e. 65535 or the max. amplitude value from the sensor (3.3V). Right now I get zero values on black line but if set offset 5%of...
View ArticleForum Post: Problem with TX-SDK-V2 kit
Reference module : TX-SDK-V2 Command number (from Farnell) : 4500202636 Hello, I am from Tours’s University where a part of my activity is focused on research aspects, mainly on ultrasonic probes...
View ArticleForum Post: RE: LM98714
Hi Hooman, Thanks for your Reply, Our INCLK is 48Mhz for LM98714 , and maximum clock frequency for CIS clock is 10Mhz, As for the information required for you, i have attached the Datasheet for your...
View ArticleForum Post: RE: Problem with TX-SDK-V2 kit
Hi Dominique, I would replace both the LM96550 & the LM96530 . Regards, Hooman
View ArticleForum Post: RE: Problem with TX-SDK-V2 kit
Hi Holman, thanks for your reply, but I don't understand why this components would have burned since no manipulation error were done. I think that if this component is changed without knowing the...
View Article