Forum Post: RE: AFE4900: about datasheet
Ishikawa-san, The AFE4900 is under selective disclosure only so we do not want to discuss on a public forum. Please go to the product folder and click the "Request Now" button....
View ArticleForum Post: RE: ADC128S102QML-SP: ADC128S102QML-SP
The way it typically works using a diode bridge. The current source is set to have compliance limit of 1ma while attempting to drive to a voltage. In this case the voltage will be 0v. Under this...
View ArticleForum Post: DAC38J84: Question about speed
Part Number: DAC38J84 I am a bit confused about the speed of this product. In DAC37J84 , DAC38J84 's data sheet Table 11, If interpolation is chosen to be 1, does it mean that each channel can output a...
View ArticleForum Post: RE: DAC38J84: Question about speed
Weiyu, your understanding is correct. -Kang
View ArticleForum Post: RE: ADS122U04: ADS122U04 Continuous Conversion mode outputs zeros
Hi user5870291, Welcome to the E2E forum! In your while loop you are continually reading the buffer, but data at 20sps only becomes available every 50ms. So when using the automatic data read mode, you...
View ArticleForum Post: RE: TX517: Disallowed Logic States and Example Input Data Set of...
Hi Hiroshi-san, How are you? It's sorry for missing the detail description of conditions (as below): When the condition of HV0x = -1.9V required, this is only based on INP0x=ON and INN0x=ON at the same...
View ArticleForum Post: RE: ADC12J4000EVM: Sample Mapping and Ordering
Hi Steve If I work through the data in the lane probes shown above using the same procedure I used in that other thread that I referenced, I see the correct data/ordering in all cases. What changes...
View ArticleForum Post: RE: ADS114S08: ADC input range with 5V ref, AGND with gain.
So do you have any ADCs that can read 0V- 0.125mV with gain internal gain of 32 when configured to do so by SW AND read 0-5V with no gain when configured to do so? All single ended.
View ArticleForum Post: RE: ADS114S08: ADC input range with 5V ref, AGND with gain.
Need a totla of 16 channels that can do that. Of course in the fastest most cost effective way possible.
View ArticleForum Post: RE: TSW14J56EVM: LEDs D1 to D8 wont turn on
Hi Erik Please let us know if you have got this working, or have any information to share that will help debug the problem. Best regards, Jim B
View ArticleForum Post: RE: ADS1282EVM-PDK: Problems using the evaluation board in...
Hi Hiago, Unfortunately, ADCPro isn't supported to work with Windows 10. However, I've seen some people get it to work though:...
View ArticleForum Post: RE: ADS1675REF: What O/S version is supported?
Hi Glen, Welcome to our forum and thanks for your post! I don't believe we've ever tested the ADS1675REF on Windows 10, but Windows 7 should work. Can I send the source code to the email address in...
View ArticleForum Post: RE: ADS1274: Chip failure Root Cause Analysis
Hello Brian, Welcome to our forum and thank you for your post! This issue has come up in the past. Almost always, it seems to be caused by a ground potential difference that develops between AGND and...
View ArticleForum Post: RE: ADS114S08: ADC input range with 5V ref, AGND with gain.
Hi Greg, our ADS1120 (SPI), ADS112C04 (I2C) and ADS112U04 (UART) could measure single-ended signals using an external 5V VREF while providing gains of 1, 2 and 4. The devices can only support four...
View ArticleForum Post: RE: ADC12DJ3200EVM: ADC12DJ3200EVM and TSW14J57 - JMODE3 problem
Hello Sai I think I may have a solution for the JMODE3 issue. There are .ini files associated with each ADC operating mode for each capture board. The files for the TSW14J57EVM Rev E are located in...
View ArticleForum Post: RE: ADS8361: Getting started with ADS 8361
(Please visit the site to view this file) Hi Aditee, See if this works for you.
View ArticleForum Post: RE: ADS8881: ADS8881EVM-PDK Export the data
Hi Hiroaki, Yes, you can export data from ADCPro to Excel. Getting two EVM's to be synchronized though is still going to be an issue. At a minimum, you'd need to be running them on two different PC's....
View ArticleForum Post: RE: ADS130E08: Sample C code and password for zip
Hi Eduardo, This is taking a lot longer than I expected it to, so please forgive the delay.
View ArticleForum Post: RE: ADS8900BEVM-PDK: ADS8900BEVM-PDK is not getting powered...
Hi Yuri, It sounds like you have a working solution. The 5.5V supply on TP1 is limited by the PHI board to ~120mA, which is enough to power the evaluation board. However, if you have additional loads...
View ArticleForum Post: RE: ADS7953: Manual Mode Timing Diagram
Hi Eric, Please feel free to reply to this post if you have any other questions on this subject. Thanks, Keith N.
View Article