Forum Post: AFE4300: ESD Protection Diode
Part Number: AFE4300 Hello, I am using afe4300 to measure BCM. I am aware i need to use esd protection diode for the connection between the board and the electrode. Is there any TI part number for...
View ArticleForum Post: RE: ADS131E06: Using ADS131e06 chip without monitoring DRDY pin
Joseph and Brian, Thank you so much for your valuable inputs.. @brian, I checked your thread, but you were sending data (or SCLKS) Byte by Byte right ? As per my understanding (please correct me if I...
View ArticleForum Post: ADS1256: ADS1256 not responding
Part Number: ADS1256 Hi, ADS1256 is not responding. i have set my SPI clock to 4.5MHz and mode1. I tried to read all the registers one at a time using two byte command and my dout is sometimes 00 and...
View ArticleForum Post: RE: DAC38RF89: Ask for help of DAC38RF89 configuration.
Hi Eben, Thank you for your answer. Today ,I just got the idea,and I thought I got the way to slove this problem. Now,I have a new idea,I want the DAC38RF89 worked at the LMFS=82380, So ,I can put a...
View ArticleForum Post: RE: ADS1256: ADS1256 not responding
Hi Roobini! I'm sorry to here that you are having trouble with the ADS1256 . Can you grab a screen capture from an oscilloscope or logic analyzer that shows your RREG command sequence? Please include...
View ArticleForum Post: RE: ADS1261: ads1261EVM cannot be detected by software...
Hi v one! Welcome to our e2e Forum! Can you tell us what shows up in your Control Panel>Device Manager once you plug in the ADS1261EVM ? Is it possible that you inadvertently erased the flash...
View ArticleForum Post: CCS/ADS1293EVM: 1293
Part Number: ADS1293EVM Tool/software: Code Composer Studio Hi I want to have the source code of ADS1293EVM ?
View ArticleForum Post: RE: ADS1115: Device Reset Operation during Supply Voltage Transient
Hi Joseph, Thanks for your prompt reply! I am checking the BMS in bench test. The VDD of ADS1115-Q1 is pretty stable during the relay switching period and continuous communication was also monitored on...
View ArticleForum Post: DAC5652AEVM: Configuration and setup for Zedboard and DAC5672evm
Part Number: DAC5652AEVM Hi, I have the following configuration: 1) Zed board connected as data source; output = 1MHz 14-bit sine output. 2) TCXO generating 40MHz LVCMOS output as clock reference. 3)...
View ArticleForum Post: AFE5809: TIDA-00419 SONAR Design Using AFE5809.
Part Number: AFE5809 Hi All, We are using AFE5809 in one of our project and we are taking TIDA-00419 SONAR Design as reference for our project. In reference design they have used Analog Control Voltage...
View ArticleForum Post: DAC121C085: Question about DAC121C085 Vout
Part Number: DAC121C085 Hi, I am trying to use DAC121C085 with xtr116 for 4-20mA output. I saw a design for DAC8551 with xtr116 and DAC8551 has a RC circuit which connected to Vref of XTR116 . Is that...
View ArticleForum Post: RE: ADS1256: ADS1256 not responding
Hi, Sorry for the delay. I have attached the screenshots of sclk vs din, sclk vs dout, sclk vs cs. Awaiting your response Roobini.
View ArticleForum Post: RE: ADS1261: IDAC specification
Hi Chris Hall, Thank you for your reply. I have additional question about "Different current magnitudes" . I draw a image of this. When IDAC1=500uA and IDAC2=1000uA, "Different current magnitudes"...
View ArticleForum Post: AMC7836: About AMC7836
Part Number: AMC7836 Hi dear supporting team, for AMC7836 , which has SPI connect to FPGA, if below scenario happens: 1) if IOVDD =0V, and AVEE\AVSS_B/C/D floating, what's the possible consequence?...
View ArticleForum Post: RE: AFE1302 Reference Design
Thanks for your previous answer! I am interested in the connection circuit of a XTAL to similar circuit. Of course, I've seen the VCXO circuit layout in figure 4 of the datasheet. But the basic...
View ArticleForum Post: RE: DAC70508: DAC Output off by a factor of 4
Hi Alicia, As Kevin pointed out, your code is LSB aligned . Did you get a change to correct and test? Regards, Uttam Sahu Applications Engineer, Precision DACs
View ArticleForum Post: ADS1220: suitable IC for RTD application
Part Number: ADS1220 Hi, Doest TI have ADS or OPA or INA IC that can meet accuracy +/-5℃ from -40 to 650 ℃ and error 1% from 650 to 950℃? RTD by use PT200 and extend to 950℃ and need to sense four RTD.
View ArticleForum Post: RE: ADS8320: SPI ADS8320 and microcontroller connection (Atmega1280)
We placed the ADC directly on the board. there are no wires at all. And they installed the RC filter, everything became a little better, but the last 4 bits still jump a lot. We also tried to measure...
View ArticleForum Post: RE: ADS54J60: ADS54J60 DC correction effecting LSB (bits stuck)...
(Please visit the site to view this file)Jiri, Please see the attached document regarding this issue. Regards, Jim
View Article