Forum Post: ADC12DL3200EVM: ADC12DL3200EVM
Part Number: ADC12DL3200EVM We would like to connect the ADC12DL3200EVM board with Xilinx VCU118 Evaluation kit byway of the FMC connectors. The ADC12DL3200EVM FMC connections don't align with the...
View ArticleForum Post: RE: ADC128S102: How much speed can be achieved practically using...
Hi Priyanka, Welcome to our e2e Forum! For Q1) please review section 7.4 of the ADC128S102 datasheet, paying particular attention to the second paragraph in that section. For Q2, you can still maintain...
View ArticleForum Post: RE: DAC38J82EVM: DAC3XJ8XEVM Installation issue with windows 10...
Hi, MS Windows 10 Enterprise LTSC (2018). Please find a copy error message screen shots attached with this reply. Thanks Jagadeesh
View ArticleForum Post: ADS54J66: Interfacing the EVM with an FPGA board through the FMC...
Part Number: ADS54J66 Hello, Here is what I'm trying to do: Interface the ADS54J66EVM board directly with a Xilinx KX705 FPGA board, without using any interposer card in the middle. Essentially, I want...
View ArticleForum Post: RE: ADS1299: DRDY Always Pulled High and DOUT does not respond to...
Hey Tom, Sorry for the delay, here is a copy of the schematic.
View ArticleForum Post: RE: ADC12DL3200EVM: ADC12DL3200EVM
Hi Kirk We don't currently have an adapter board to enable connection to a standard FMC connector. It is something we are considering but isn't in progress yet. The alternative would be to do...
View ArticleForum Post: RE: ADS54J66: Interfacing the EVM with an FPGA board through the...
Hi Aditya We have received your question. One of our ADS54J66 experts will provide a more detailed response as soon as possible, however due to the holidays the response may be delayed until the middle...
View ArticleForum Post: RE: ADS1299: DRDY Always Pulled High and DOUT does not respond to...
Thanks Thomas, I still don't see how C13 and C11 are actually tied to any ground (0V or VSS) node. Your schematic does not seem to match the layout, at least not from the partial portion that you...
View ArticleForum Post: ADC128S102QML-SP: maximum output current
Part Number: ADC128S102QML-SP What is the specified maximum output current for ADC128S102QML-SP for source and sink? The data sheet only lists Voh and Vol test conditions of 200uA and 200uA to 1mA...
View ArticleForum Post: RE: ADS1299: DRDY Always Pulled High and DOUT does not respond to...
Hey Tom, Both C11 and C13 are tied to vias leading to the ground plane @ 0V. On the schematic they are in the bottom left tied from 3v3 and VDD to 0V respectively.
View ArticleForum Post: AFE4400: AFE4400 diagnostic
Part Number: AFE4400 How to perform auto-diagnostic of afe4400 ?
View ArticleForum Post: RE: AFE4490: AFE_RESET pin
Hi Harielamadu, Yes, your interpretation is correct. Regards, Prabin
View ArticleForum Post: RE: AFE4400: AFE4400 diagnostic
Hi Anish, Diagnostic mode is enabled by setting "DIAG_EN" bit. Diagnostics sequence starts when this bit is set. At the end of the sequence, all fault status are stored in the DIAG: Diagnostics Flag...
View ArticleForum Post: RE: AFE4405: The performance of the AFE4405
Hi Mats, Since AFE4405 is still under NDA, lets take this discussion offline. Regards, Prabin
View ArticleForum Post: RE: AFE4400: AFE4400 diagnostic
Hi Prabin, I have already gone through the datasheet and understood the diagnostics sequence. From customer point of view, the device must detect probe faults on its own. What i want is that on what...
View ArticleForum Post: ADS8684: HOW to use the ADS8684 To monitor battery cell
Part Number: ADS8684 HI Sir I want to monitor the battery cell by 4 series, could i use the ADS8684 to do this? or did you have any solution to do it? thanks
View ArticleForum Post: ADS1262: ads1262
Part Number: ADS1262 ads1262 is for weight scale application suitable for more than 2,50,000 counts??
View ArticleForum Post: RE: DAC3482EVM: Documentation and design files
Thanks Kang, This link works fine and I'm able to download the content. In many other reference designs and EVMs TI provides the original design files (.dsn, .brd), but not in this one... Is it...
View ArticleForum Post: RE: ADS1282: Is it okay to partially power down the ADC...
Hi Chris, Thanks for the response. I also appreciate the advice about the LDO pull-down. This is something that I will look in to. Regards, Andrew
View ArticleForum Post: ADS8638: Battery Cell Voltage Monitor
Part Number: ADS8638 Hi Sir I saw ADS8638 datasheet have a battery cell voltage monitor used with INA149 Have any ADC could be used for this application without INA149 ? Thanks
View Article