Forum Post: DAC900: About the configuration of DAC900
Part Number: DAC900 Hi TI expert, I wonder if DAC900 's VA(analog supply) and VD(digital supply) can both be +3.3V? I have this question because DAC900 's datasheet says that its VA and VDs' typical...
View ArticleForum Post: ADS1118: using the ADS1118 with a K type thermocouple for...
Part Number: ADS1118 hii i came across your ADS1118 witch has a cold junction compensation built in feature build in . i have an application where i want to measure temperatures below 150C for...
View ArticleForum Post: TSW1400EVM: Ports cannot get listed properly in Device Manager
Part Number: TSW1400EVM Hi Team, My customer follows the guideline indicated in the user guide of "TSW140x High Speed Data Capture/Pattern Generator Card" step by step but cannot get the ports listed...
View ArticleForum Post: DAC38J82EVM: power source
Part Number: DAC38J82EVM Hello All, My customer just ordered DAC38J82EVM . At the User's guide I found that external power source +5V barrel jack 5V/3A is needed. I assume TI does not supply that power...
View ArticleForum Post: RE: ADS8684: HOW to use the ADS8684 To monitor battery cell
Hi Alex, As noted in the datasheet, the ADS8684 supports bipolar voltage ranges of +/-2.56, +/- 5.12 and +/-10.24 and unipolar voltage ranges of 5.12 and 10.24V. Depending on your battery cell voltage,...
View ArticleForum Post: RE: ADS1262: ads1262
Hi Kinnari, I suspect you mean 2,500,000 counts, which is about 21.25 bits of accuracy. Table 2 on page 28 of the ADS1262 data sheet provides you with both ENOB and (Noise Free Bits) detail for various...
View ArticleForum Post: RE: ADS8684: HOW to use the ADS8684 To monitor battery cell
HI Sir IF I have a battery Cell which have 6 series,Can I use the ADS8684 to monitor every cell ,don't care the comom mode voltage? ex:ch1,to monitor the first cell ,ch2 to monitor the second cell ,ch3...
View ArticleForum Post: RE: ADS8638: Battery Cell Voltage Monitor
Hi Kai, Are you working with Alex? This sounds like a similar question: e2e.ti.com/.../758104
View ArticleForum Post: RE: ADS8684: HOW to use the ADS8684 To monitor battery cell
Hi Alex, Have you looked at parts like the BQ76925 ? Take a look at the website: www.ti.com/.../overview.html
View ArticleForum Post: RE: ADS1293EVM: ADS1293EVM SW time scale inconsistency with real...
Hi Alex, Maybe this question shall be addressed to someone else but as a continuation to the major topic, I will try to ask it here. So I got the NI-8452 device. I have successfully managed to...
View ArticleForum Post: RE: ADS1118: using the ADS1118 with a K type thermocouple for...
Hi Aied, Our ADS1118 expert is on holiday at the moment, so there may be some delay in fully answering your application question. Can I ask you for a little clarification in the mean time though? Are...
View ArticleForum Post: RE: ADS1299: DRDY Always Pulled High and DOUT does not respond to...
Hey Tom, no I am unable to read anything off the registers. I can use the oscilloscope to see the correct command being sent, but there is nothing returned on the DOUT pin. VCAP1-4 are respectively,...
View ArticleForum Post: RE: ADS5401: Binary to Decimal conversion for temperature sensor...
Hi Yusuf-san, It has passed more than 10 days from your last reply. Could you let me know the current status of your checking? Regards, Takashi Onawa
View ArticleForum Post: RE: ADS1298: Suggestion for an appropriate TI made microcontroller
Hi Abhinav, As above answer, the SPI interface is a simple requirement. You need provide more information. Give you a check list: 1. Flash and RAM size? 2. Pin numbers (GPIO numbers)? 3. Sample rate?...
View ArticleForum Post: TSW1400EVM: TSW1400EVM
Part Number: TSW1400EVM Hi, we are interfacing ADS5294 Evaluation board with TSW1400EVM we are tried generating ramp in ADS5294 GUI and Captured Time domain Data in HSDC pro software we are getting...
View ArticleForum Post: ADS1115: Have noise issue and when and how to calibration
Part Number: ADS1115 Dears, We use ADS1115 to sample the Voltage and Current signal，we find two question when we test it . Q1:when the signal output is 0V or no connect to the transducer,sometimes a...
View ArticleForum Post: ADS7953: power up sequence
Part Number: ADS7953 Hi Team, What's the power up sequence requirement between CHx input voltage and +VA？ What if CHx input voltage power up prior to the +VA, dose it have the risk of Voltage flow...
View ArticleForum Post: RE: AFE4420: AFE4420
Dear Prabin, if i can contact you with email ? could you provide your email address to me ?
View ArticleForum Post: RE: ADS114S06: SPI Communication with ADS114S06
Hi Jehan, From your description it appears that the SPI connections are incorrect. MOSI (master out slave in) should connect to DIN and MISO (master in slave out) should connect to DOUT of the...
View ArticleForum Post: ADS1298: ADS1298 sample code in c language
Part Number: ADS1298 is there sample code for reading ADS1298 in c language.
View Article