Forum Post: RE: AFE5816EVM: AFE5816EVM with TSW1405
Hi Mark, Thanks for using AFE5808 EVM and AFE5816EVM . Actually according to the User's Guides, these two EVMs are recommended to connected to TSW1400EVM . Therefore we will look into your questions...
View ArticleForum Post: RE: AFE5809: Question on Differential termination resistor...
Hi Yi, How are you? Thanks for using AFE5809EVM . Yes, I will reply to your question very soon. Thank you very much! Best regards, Chen
View ArticleForum Post: RE: AFE5816EVM: AFE5816EVM with TSW1405
(Please visit the site to view this file) Hi Mark, First, could you please try the attached .ini file used for AFE5808A used for 12bit mode only. Thanks!
View ArticleForum Post: RE: how much sample rate and bandwidth do i need for this waveform?
Hi Tom, Thank you for the answer. rise and fall times are 1 and 2 us respectively. rise time is more important. the voltage is design-able in the analog section. ( ie 0-1 V, 0-3V, ... ) 10 bits of...
View ArticleForum Post: RE: ADS114S06: SPI Communication with ADS114S06
Hi Bob, We checked all supply voltage at all pins of ADS114S06 , we observed all voltages are sufficient as mentioned in datasheet. At present state we observed spikes of 60µSec from DOUT pin of...
View ArticleForum Post: RE: AFE5816EVM: AFE5816EVM with TSW1405
Thanks Chen, for the ini file and for the fast action. I will have a detailed look later in the new year. Just have tried quickly and it seems to work, I can see the test pattern, so the communication...
View ArticleForum Post: AMC7834: CLAMP Configuration (0x17) R/W problem
Part Number: AMC7834 Should all of the bits 0..6 in CLAMP Configuration (0x17) be readable to indicate their status? I find that Bit 6 (PAON) does change to reflect its status, but the lower Bits 0..5...
View ArticleForum Post: ADS1281: Wake up flag
Part Number: ADS1281 we are experiencing a problem during our start up process. We are unsure whether this comes from the ADS1281 wakeup sequence or the CPU startup sequence. Does the device have a...
View ArticleForum Post: RE: DAC38J82EVM: DAC3XJ8XEVM Installation issue with windows 10...
Jagadeesh, Yes there is a chance that the GUI is not supported on Windows 10 , because the GUI uses LabVIEW 2010 Run-Time engine which is not compatible on Windows 10. (i.e., NI doesn’t guarantee the...
View ArticleForum Post: RE: ADS8588H: Need OPAMP BUFFER for ADS8588H
Hi Ramesh, Can you tell us a little more about the sensor you are trying to interface with? The ADS8588H has a high impedance input network and does not necessarily need the same drive requirements as...
View ArticleForum Post: RE: AMC7834: CLAMP Configuration (0x17) R/W problem
Hi Michael, I will confirm this in the lab after the holiday. Thanks, Paul
View ArticleForum Post: RE: DAC8562: DAC8562SQDGSRQ1 katchup
Hi Munir, The DAC8562QDBSRQ1 device passed latch up testing with accordance to AEC-Q100-004D. www.aecouncil.com/.../AEC_Q100-004D.pdf Thanks, Paul
View ArticleForum Post: RE: AFE5809: Question on Differential termination resistor...
Hi Yi, How are you? Thanks for using AFE5809 device. for your question #1, the AFE5809 differential inputs have very high impedance (around 100KHz differentially). Please look at the data sheet page...
View ArticleForum Post: RE: AFE5809: Question on Differential termination resistor...
Hi Yi, How are you? Sorry there was a typo. the following is the correct number: for your question #1, the AFE5809 differential inputs have very high impedance (around 10Kohm differentially). Please...
View ArticleForum Post: RE: AFE5809: Question on Differential termination resistor...
Hi Yi, If you are using either LVDS or LVPECL to drive the AFE5809 input clock, we suggest the following configuration (shown on the AFE5809 data sheet): Thank you! Best regards, Chen
View ArticleForum Post: ADS1261EVM: The Register Map did not show and the Delta -Sigma...
Part Number: ADS1261EVM
View ArticleForum Post: RE: ADS1261EVM: The Register Map did not show and the Delta...
I have two boards, the situantion are same! I do not konw what is wrong?
View ArticleForum Post: RE: ADS8588H: Need OPAMP BUFFER for ADS8588H
Hi Tom, Wish U a happy New year 2019. Actually,the ADC ADS8588H is intended to be used for power electronics application (DC-DC Converter & DC-AC inverters). We need to sense high frequency current...
View ArticleForum Post: RE: AFE5809: Question on Differential termination resistor...
Hi Chen Thanks for quick reply. Quote "for your question #2, could you please let us know where you found: -----------But I also see some design as "Clock source--> AC caps--->100ohm --> AFE"...
View ArticleForum Post: RE: AFE5809: Question on Differential termination resistor...
But I thought AFE5809 can accept LVPECL clock input， so it's input should be equivalent to an LVPECL reveiver.....
View Article