Forum Post: RE: TSW14J56EVM: Simulation doesn't work
Mhed, Try the following to resolve errors shown in Model Sim RTL Simulation 1. Please copy and replace the attached Verilog files- dec_data_capture_gz.sv, enc_data_gen_gz.sv & jesdcon204b_top.v in...
View ArticleForum Post: RE: Compiler: TSW14J57EVM+ADC12DJ3200/ADC08DJ3200
Guangxin, 6.4Gsps is not possible. The max practical USB3.0 throughput possible is only 2.7 Gbps to transfer the data to PC RAM without any post processing. Writing to hard drive and any channel...
View ArticleForum Post: ADS1292ECG-FE: ADS1292ECG-FE Labview PC software source file
Part Number: ADS1292ECG-FE Hi All, I am using ADS1292ECG-FE devkit for a project. The ECG waveform could be shown in the Labview PC software. However, I can't find the Labview PC software source code....
View ArticleForum Post: RE: ADS1292ECG-FE: ADS1292ECG-FE
I am also looking for the Labview PC software source file. Because I have some problem with these codes: for ( ucLoopCnt =0 ; ucLoopCnt > 8 ; // Low byte B7-B0 } I know the first loop is for...
View ArticleForum Post: RE: ADS1299: DRDY Always Pulled High and DOUT does not respond to...
Hi Thomas, If your power scheme is setup as shown in Figure 78, VCAP1 is fine. How are you controlling /CS, /RESET and /PWDN?
View ArticleForum Post: ADS1284: Current status
Part Number: ADS1284 Hi team, Customer wants to use ADS1284 in their project, but I find there is no detailed price and sample in web. Could you help check the current status and schedule of ADS1284 ?...
View ArticleForum Post: RE: AMC1303M2520: Datasheet mismatch on digital interface...
Hi Li, As soon as I get confirmation from the digital design team, I will let you know if it's 2 or 4 clock cycles.
View ArticleForum Post: RE: how much sample rate and bandwidth do i need for this waveform?
Hi Ras, Let me send you over to the High Speed data converter team. They should have something to satisfy your application needs.
View ArticleForum Post: RE: ADS1259-Q1: Safety Analysis - FIT rates acc. SN29500
Hi Michael, I wish you a Happy New Year. I will contact you shortly by email again. Regards,
View ArticleForum Post: RE: ADS1298: ADS1298 sample code in c language
Hi Vindhyachal, You seem to have some extraneous chip select toggles (like the last one in your setup before the send_command (SDATAC)). That being said, are you getting the expected results from this...
View ArticleForum Post: RE: ADS1284: Current status
Hi Will, the ADS1284 is a fully released product. One of my team members will contact you with the information you need. Regards,
View ArticleForum Post: ADS1217: DRDYn signal is always "clocking" (high = 20us, low = 30ms)
Part Number: ADS1217 Everything seems to be working ok, but I dont know why the DRDYn pin is always driving this signal even after power up!!! Below pin status: ( I am not issuing any commands to ADC )...
View ArticleForum Post: RE: ADS1217: DRDYn signal is always "clocking" (high = 20us, low...
also, PDWNn = High Thank you
View ArticleForum Post: RE: AFE5808: Questions for AFE5808A Example Registers...
Hi Jacky, How are you? Thanks for helping customer using AFE5808A device. We will look into your questions and I will reply to you soon. Thank you! Best regards, Chen
View ArticleForum Post: RE: ADS1292ECG-FE: ADS1292ECG-FE Labview PC software source file
Hello Hua, Thanks for your post! Please accept my friend request and I will send you a private message with the files.
View ArticleForum Post: RE: ADS1292ECG-FE: ADS1292ECG-FE
Hi Dominique, Please accept my friend request and I will send you the labview source code. Additionally, this thread may help you convert code to voltage: e2e.ti.com/.../1363393
View ArticleForum Post: RE: ADS1259: adjust reference voltage to input range
Hi Pavel, The ADS1259 can measure differential voltages up to +/- Vref. Therefore, your reference voltage will need to be at least 3.6V, but I see no issues with using a larger reference, such as 5V. I...
View ArticleForum Post: RTOS/ADS1118: Best practices for using Tiva C TM4C1294 QSSI with...
Part Number: ADS1118 Tool/software: TI-RTOS I'm very new to programming TI processors so I hope my question isn't way off base. I will be using a configuration that has a Tiva TM4C1294 processor. It...
View ArticleForum Post: ADS124S06: Differential measurement
Part Number: ADS124S06 Hi all, I have a doubt regarding differential measurement with ADS124S06 . Basically I want to measure a DC voltage between AIN1 (configured as positive input) and AIN3...
View ArticleForum Post: RE: DDC264: DDC264EVM
Hi David, Thanks for letting us know. By the way, when you are running DDC264EVM you also need to connect an adapter (small-size) board onto it. Also could you also follow the DDC264 GUI? If still not...
View Article