Forum Post: RE: AFE5809 CW and TGC paths
Thank you, Fabiowe are working at a project which uses up to 128 receivers. Use of an integrated 8 CHS receiverslike AFE5809 instead of separate ADCs and DDCs reduces the complexity of the...
View ArticleForum Post: RE: help in using pulser IC(lm96550) to generate +/-15v pulses
Hi Chandu,As you are probably aware, the inputs P0 & NO can't be both 1 at the same time. With a 10Hz square wave, do you know the rise & fall time of waveform? I am afraid that the if rise and...
View ArticleClik here to view.
Forum Post: RE: About the software of AFE5809EVM.
Dear Fabio-sanThank you for the advice.It all Uninstalled and Install again.A result is written to below.Process 2: A port did not appear in a device manager but the port was added to the...
View ArticleForum Post: RE: Lots about AFE's but what about row gate drivers ?
Hi Randal,the MPT57605 is an OBSOLETELCD Gate Driver.As stated previously, at the present time TI does not offer a gate driver solution for -X-Ray FPD panels.BRGuglielmo
View ArticleForum Post: RE: help in using pulser IC(lm96550) to generate +/-15v pulses
Hi Chandu,You need to set tx_en to '1' in order to see the pulse pattern at the output.Regards,Charles
View ArticleForum Post: RE: where is the programming info for LM98714/22 ??
ah!wrong forum to start searching here i have found other posts point ti them .. Thanks R
View ArticleForum Post: RE: functioning of LM 96570
Hi Mariusz,Would you please send me(tu.praveen@gmail.com) a copy of your app for calculating beamforming delays? we are working on a ultrasound imaging project.Thanks in advance!
View ArticleForum Post: RE: where is the programming info for LM98714/22 ??
Hello Ralph,Did you find the information you were looking for?I have the "LM98714 Programming and Operation Manual" (dated March 2012) if you have not received it?I also have the complete datasheet...
View ArticleForum Post: RE: TX-SDK-V2 Emulator
Hi Charles and Mariusz,Thank you very much for your quick and resourceful answers. We will thoroughly read all the DUT data sheets and disconnect the ±50 and ±40 power supplies when testing.Kindest...
View ArticleForum Post: RE: How to control T/R switch in TX-SDK-V2 externally
Hi Fathima,You can disconnect the resistor RA27 and then connect your control signal directly to pin 59.Regards,Charles
View ArticleForum Post: RE: functioning of LM 96570
Hello Praveen,In the attach PDF I try to show a possible solution for a clock distributions from crystal source through TI LMK03000 and LMK01010 Timing products to the LM96570 and FPGA , plus...
View ArticleForum Post: RE: Synchronizing Rx and Tx sides of Ultrasound system using EVMs
Hi Mariusz, Thank you very much for the information.
View ArticleForum Post: RE: Availability & Substitutes for CCD TC237B
I am looking for up to 700 off part number TC285SPD-B0. I have been informed that the tsunami in Japan caused a loss of being able to continue supply. Is there anyway within the TI loop that I can...
View ArticleForum Post: RE: Availability for CCD TC285SPD-B0
Hi David,This part number was discontinued in 2011.Unfortunately there is no residual inventory remaining.We do have limited remaining inventory of alternate part number TC285SPD-30. This device is...
View ArticleForum Post: VSP5610 question
HiI have a question about VSP5610.1)How to connect the CMOS image sensor?2)How to connect the LED(a light source of Image Sensor)?3)Is there any document of circuit design sample?Please send me the...
View ArticleForum Post: RE: LM98714 INCLK min range
Hello Hooman. Thank you for reply. The min INCLK :5MHz understood. and thank you It teaches influence for 5MHz low-level. Best regard Ben from japn
View ArticleForum Post: RE: AFE5809 LNA
Ran,No, the AFE5809 cannot operate in differential input mode. INM must be tied to ground through an external capacitor.Thanks,Chuck Smyth
View ArticleForum Post: RE: Time period of TX_SYNC_IN for AFE5809?
Hi Praveen,You will find the answer on your question on page 53 of the AFE5809 datasheet.Regards,Mariusz
View Article