Forum Post: RE: need guidence in powering of Tx_Sdk_V1 EVM
Hi,Please some body who knows about Tx_sdk_v1 powering answer to my questions. It is usefull and urgent for me. thank you.regards,chandu.
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi Chandu,1) The capacitors CB51 to CB58 are there to model the transducer parasitic capacitance. If you are connecting the TX_SDK_V1 board to the transducer, then you don't need those caps anymore and...
View ArticleForum Post: RE: doubt in Tx_sdk_v1 EVM
Hi Chandu,Please see my earlier reply. Basically, just apply +15V to VPP and -15V to VNN if you wan to generate +/-15V at the output.Regards,Charles
View ArticleForum Post: RE: need guidence in powering of Tx_Sdk_V1 EVM
Hi sir,Thanks for valuable information.If you don't mind let me confirm again about the 4th answer in last reply.By giving single 3.3v to the Tx solution board Is it possible to GUI connected to the...
View ArticleForum Post: RE: need guidence in powering of Tx_Sdk_V1 EVM
Hi Chandu,Yes, you can communicated the Opal Kelly board with the TX_SDK board.Regards,Charles
View ArticleForum Post: RE: About TX-SDK-V1 powersupply?
Hi Spiros,To get positive supply voltage from the power supply, the -ve connection is connected to ground and the +ve connection is connected to the desire positive voltage. To get negative voltage...
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi sir,Thank you for being informative.I am facing error in GUI getting connected to the hardware set up. And the power supplies are vpp(50v)=15v, vnn(-50v)=-15v, vdd=10v, vdn=-10v ,vsub=-20v, 3.3v,...
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi,thank you for your reply.I think no problem with opal kelly board driver installation because, It was showing that connected in device manager.And opallkelly board drivers are supported for...
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi Chandu,When I mention the software was written for Windows XP, I mean the TI GUI software not the Opal Kelly. If you can find a Windows XP machine, it might be good to try it.As for training, I...
View ArticleForum Post: AFE5801 stability issue?
Hi, I am using AFE5801 for my imaging board and have been experiencing some strange behavior.I have MAXIM14811 pulser, MAXIM4937 TRSW.When I send out a pulse, AFE first gets saturated and goes into a...
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
hello sir,sorry for asking again, But I did not violate the absolute ratings of Beamformer, pulser and switch as per data sheets.When I was first gave the power supplies to the board, That time in...
View ArticleClik here to view.
Forum Post: RE: Questions about TX-SDK-V2 EVB
Hi Chandu,I am sorry for your trouble. But did you power up the 1.8V supply before powering the 3.3V supply? (As you posted on Aug 12). You should power up the 3.3V then the 1.8V...
View ArticleForum Post: Lots about AFE's but what about row gate drivers ?
Hello ForumI am designing with the AFE0064 for column readout and can find little info on designing the other part of the equation - biasing the TFT gates in an Xray panel. Row drivers.Are there...
View ArticleForum Post: RE: Lots about AFE's but what about row gate drivers ?
If this is truly the case, what is the MPT57605256-OUTPUT TFT GATE DRIVERall about?
View ArticleForum Post: RE: LM96551
Hi Mariusz,For TX circuit I STRONGLY recommend a multilayer PCB. VPP/VNN should be a plane and VPF/VNF should be a splitted plane of VPP and VNN, respectively. Regarding your suggestion mentioned above...
View ArticleForum Post: RE: LM98620 Data sheets
Hello Bernardo,The full LM98620 datasheet is shared with customer who have an NDA (non-disclosure agreement) in place with Texas Instruments. This device is in production and available.Do you have a...
View ArticleForum Post: RE: Time of Flight Chipset, OPT8140 / OPT8130, VSP5324 and OPT9110
Hello,The CDK you describe fits exactly our needs at Eikeo. Would it be possible to have an early quotation for such a CDK, as for each the differents components ( OPT8130 / OPT8140, OPT9220 and the...
View ArticleForum Post: RE: Time of Flight Chipset, OPT8140 / OPT8130, VSP5324 and OPT9110
Erwin,I have replied to your email to close this thread.
View ArticleForum Post: RE: AFE5809 CW and TGC paths
Hi Antonello,Please find the answers below highlighted in red.1.Would it be possible to operate the CW and TGC paths on the same time?[Fabio] No, the part is designed to work either TGC OR CW. See...
View ArticleForum Post: RE: About the software of AFE5809EVM.
Satoshi-san,I tried to reproduce your issue in the Lab but I wasn't able to get those errors.Could you please uninstall the AFE5809GUI, TSW1250 GUI and any TUSB3410 driver installed?Then please refer...
View Article