Forum Post: RE: ADS8528: How to initialise the VREF settings correctly
Hello Juergen, I will check the detail and get back to you soon. Thanks. Regards Dale
View ArticleForum Post: RE: ADS8688: Problems starting conversion.
Hello Stewie, I will check and get it back to you soon, thanks. Regards Dale
View ArticleForum Post: MSC1210Y5: Need more memory
Part Number: MSC1210Y5 Hello, We have quite old design with MSC1210Y5 and our application grows up, pushing memory capacity to maximum. This part is the biggest one of the familly. Is there an other...
View ArticleForum Post: RE: ADS1281: How to calibrate ads1281?
Hi Chris, Thanks for your reply! Firstly, the command sequence mentioned following up is that I am using with STM MCU. We could not know the calibration process of ADS1281EVM. In this command sequence,...
View ArticleForum Post: RE: ADS124S08: Multiple analog type for every channel
Bob, Can yo give me sampe for siwtch or Mux xhip (TI product) that match with ads124s08 . Thanks
View ArticleForum Post: RE: ADS5400: Does the batch number of ADS5400 affect the output?
Hi Yusuf, My customer tested both ADS5400 's on the same PCB with the same program. But the output waveform are different. I'll be providing more details when the customer gives me feedback. Thanks...
View ArticleForum Post: RE: BOOSTXL-ADS7841-Q1: Cannot get data output from ADS7841-Q1...
Hello Cynthia, Thank you for the response. I noticed that the clock cycle only toggled when you sending in data and I assume it would toggle again when there is data coming out. As the scope showed,...
View ArticleForum Post: ADS1293: 3 lead ECG application with ADS1293
Part Number: ADS1293 hi team my customer is generating a schematic for 3 lead ECG with the ADS1293 we'd like to check the following questions 1. can all the power source to the ADS1293 input at 3V ?...
View ArticleForum Post: ADS8681: Daisy chain in ads8681
Part Number: ADS8681 Hello Dale, i have one more query. in ads8681 i did the daisy chain connections for two devices exactly as follows . so while configuring the device .. SDO of the processor...
View ArticleForum Post: ADS8864: ADS8864 of ESD protection
Part Number: ADS8864 Does analog input pin include ESD protection function? If you have a feature, how much capacity? best Regards,BANE
View ArticleForum Post: RE: ADS4225: Using a SDR ADC in a DSO project
Hi Dan and thanks again for your message, Yes you are right, my bad. The devices i am thinking of driving are a second ADS4225 as the target DSO is a quad channel. Also i want to drive that clock to...
View ArticleForum Post: RE: DAC7811: About DAC7811 circuit
Hi Uttam-san, Please let me ask you an additional question. My customer is considering using the DAC7811 now. In his current design situation, the DAC 7811 needs to be controlled by a serial...
View ArticleForum Post: RE: DAC81416EVM: OSC-ALM bit high in status register
Hi Sandeep, Thank you for your query. This OSC_ALM bit is a reserved bit as per the latest datasheet. The GUI being a bit old still has this bit exposed. You can ignore this bit. The behavior is...
View ArticleForum Post: RE: DAC7811: About DAC7811 circuit
Hi Tsuyoshi-san, I think this scheme should work but I need to test it on the EVM before I can confirm. I will get back by next week. Regards, Uttam
View ArticleForum Post: RE: Deserializer - Frame grabber for LVDS & 4K LVDS video signals
Hello Davide, for these three setup you can use only one Deserializer; DS90UB948 for example. Note: Signal_1 has a high resolution, hence you will need to use dual lane mode between SER and DES to...
View ArticleForum Post: RE: DAC121S101QML-SP: Digital IO powered without power supply
Hi Kirby, Thanks for your answer. So I have again two questions : - In this case, why in the datasheet with cannot have a voltage above Va + 0.3 (and not 5.5V) on digital IO? - What is the inpact of...
View ArticleForum Post: RE: DAC7811: About DAC7811 circuit
Hi Uttam-san, Thank you very much for your prompt reply. I really appreciate your cooperation! I look forward to your answer. Thank you and best regards, Tsuyoshi Tokumoto
View ArticleForum Post: RE: TSW1400EVM: AFE5818 interface blocks
Hi Chen, thanks for the reply and for the files. Appreciate the support! Regards Mihir
View ArticleForum Post: RE: ADS5400: Does the batch number of ADS5400 affect the output?
Yusuf Hello We used the same circuit board to do the test. In the absence of any modifications to the program. The output waveforms are different. There is mention in the version that registers are...
View ArticleForum Post: RE: Deserializer - Frame grabber for LVDS & 4K LVDS video signals
Hi, thanks for the information. I've found www.ti.com/.../toolssoftware but I need to have a board. Do you know which one? Could you please explain better the reason why for signal_1 I have to use SER...
View Article