Forum Post: CCS/AFE4900EVM: AFE4900 read
Part Number: AFE4900EVM Tool/software: Code Composer Studio Hello, I read the register 0x2c of AFE4900 , the value is const 0x0FFF8C, but the register 0x2b is normal. I don't know the reason. The...
View ArticleForum Post: RE: ADC12D1800: Recommended power-up sequence for NON-DES mode...
Hello Jim. First, thank you again for the informative and thorough answer. We solved the problem following your recommended power-up sequence (thanks a LOT) but in the process we noticed that the...
View ArticleForum Post: ADS8681: Daisy chain in ads8681
Part Number: ADS8681 Hello Dale, i done the configurations as u suggested given below still getting the same resultsi.e. the only second device output not getting the 1st device output....
View ArticleForum Post: RE: ADS1293EVM: ADS1293EVM interface to the MSP430 failure
Hello, Yes, I tried all of the demos. I was using hardware in the default configuration as well. If you have any other guides or advice to manage SPI connection between ADS1293 and MSP430, I will be...
View ArticleForum Post: RE: ADS131E04: May Ads131 can replace AD9629?
Bogey, First, I'm sorry I didn't get back to you earlier. I'm not sure that the ADS131E04 work in the application because of the input range. I had mentioned the ADS131A04 earlier and that may work...
View ArticleForum Post: RE: SM73201-ARC-EV: RD 195 Safety Test Fail
Problem in the Safety Test was due to debug mode PSA_CRC calculations. Removed from the debug mode and worked like charm. Thanks for your help though, Ozino.
View ArticleForum Post: RE: TSW14J56EVM: Maximum data capture size
Hi Siavash, How are you? For your special case, we need to try it in our lab and see if we can capture such amount of data. One thing we can make sure is: when the TSW GUI runs, it would "display" data...
View ArticleForum Post: RE: LM98714: Longevity and newer device available?
Hi, LM98714 is active product and we are promoting to customers. Yes, good device to recommend. regards Shinya Morita
View ArticleForum Post: RE: TSW14J56EVM: Maximum data capture size
Hi Chen, Thank you! I greatly appreciate it. Best, Siavash
View ArticleForum Post: AMC1210: AMC1210 Reset Time
Part Number: AMC1210 Hi TI Support, I was wondering what the minimum time the RST pin on the AMC1210 needs to be held low in order for the AMC1210 to be reset? I have searched through the AMC1210 data...
View ArticleForum Post: RE: incorrect readings
Hi Michael, Would it be possible to see a schematic of the circuit? The only thing I can see from the register settings is that you are relying on the external ADC inputs, so it is possible the issue...
View ArticleForum Post: RE: ADS1281: How to calibrate ads1281?
Hi w w1, Welcome to the TI E2E Forums! Is the command sequence you showed what you are observing on the ADS1281EVM, or is that the command sequence you are currently using with the STM MCU? If you'd...
View ArticleForum Post: RE: DAC37J82EVM: Link establishment fails during ILA sequence
Branden, We have seen issues in the past when using Xilnix parts with serdes rate around 10Gbps. As a sanity check, can you try your setup with a serdes rate below 8 Gbps? What value are using for RBD?...
View ArticleForum Post: RE: SM73201-ARC-EV: RD 195 Safety Test Fail
Rahul, Great to hear that you fixed your issue. Thanks for sharing your findings. Regards, Ozino
View ArticleForum Post: RE: AMC1210: AMC1210 Reset Time
Hi Ben, Great question! One cycle of the system clock would do the trick in resetting the AMC1210 . We'll look into updating the datasheet with this detail on the next revision of the document.
View ArticleForum Post: ADS1247: Follow up on Calibration response to un-used ADC channels
Part Number: ADS1247 Hello, I have a follow up question pertaining to ADS1247 . In my application I have 5 channels for temperature measurement and each channel has an ADS1247 chip. I am using the...
View ArticleForum Post: RE: ADC12DJ3200: Explanation of Absolute Maximum Ratings for...
I'm still confused. "The maximum output swing with 200 ohm load is 5.6Vpp differential at the amplifier differential outputs. As you state, at this level each amplifier output is swinging from +1.4V to...
View ArticleForum Post: ADS62P45EVM: I want the Schematic Design of Rev.B
Part Number: ADS62P45EVM Hello, I have a request. I have a ADS62P45EVM of revB. However, there were only two revC and revD on the web. I want to get the Schematic Design of revB. If possible, I also...
View ArticleForum Post: RE: ADC12DJ3200: Power supply desig for 3 ADCs
Hi Jim, We are planning to go with 5v as chosen in EVM. But we can also use 12v. So request you to suggest us regulators for both 5v and 12 v input. Thanks, Lalit
View ArticleForum Post: RE: ADS8681: Daisy chain in ads8681
Hello Kanchan, I will check the detail and get back to you soon. Thanks. Regards Dale
View Article