Forum Post: RE: ADS1299: Unstable Data Rate (~60 SPS instead of 250 SPS)
Hi Alex, Thank you for your support! I checked power supply and these pins, but they seemed to be fine. Then I found a high correlation between the signal on CS pin and START pin (they are physically...
View ArticleForum Post: RE: CCS / TSW1400EVM： HSDC pro unable to identify to Tsw1400 via usb
Hi : The same problem arises again.The TSW1400 serial number is not identified by the HSDC Pro GUI.I took your advice.All hardware connections were checked.I find that usb is often not recognized by...
View ArticleForum Post: RE: ADS8028EVM-PDK: External Microcontroller
Hi Joseph, It's ok! Regards, Jianxiong
View ArticleForum Post: RE: ADS4249: Modifying ADS4249EVM for DC-coupled, differential input
Hi Jim, thank you. I'm looking forward to the detailed response. Best regards, Stani
View ArticleForum Post: RE: ADS131E08: ADS131E08 with Unipolar Power Supplies in a...
Hi Joseph, I think you are right, it makes much sense to me what you say. It is a pity the part needs a minimum of 2V reference. But as it is a recomendation I pehaps try to use Vref at 1.65V or 2V and...
View ArticleForum Post: TSW14J56EVM: Is it possible to customize FPGA data
Part Number: TSW14J56EVM Dear Specialists, My customer is considering ADS54J56 and TSW14J56EVM . He has questions, I would be grateful if you could advise. --- I am planning to use ADS54J60EVM plus...
View ArticleForum Post: RE: ADS131E04: strange DRDY behavior
Hi Joseph, thank you for the quick response! "Unfortunately" today I'm not at work but first thing on monday I'll try your suggestions and let you know. Have a nice weekend! Mattia
View ArticleForum Post: RE: ADC16V130: SNR SFDR performance
Hi Dan, When can I expect to receive the plots ? Please help to share the plots at the earliest.
View ArticleForum Post: RE: TSC2007: Non-responsive TSC
Hello, we didn't any power cycle during our test. We only "played" with i2c commands for a while, trying different values in Command Byte. I cannot say precisely all the steps we did, but suddenly the...
View ArticleForum Post: ADS8671: What is the output data register Address
Part Number: ADS8671 Hi TI Team, Thanks for your continuous supporting for my queries. I am using ADS8671 and ADS8900B in my design. How can I read the converted data equivalent to the analog signal to...
View ArticleForum Post: DAC8742H: Does DAC8742H has passed the physical layer test of...
Part Number: DAC8742H Hi all Now our customer use HART comunication for there pressure transmitter product,we recommend DAC8742H to our customer, but customer want to konw this part has passed the...
View ArticleForum Post: DAC3482: How do I recognize PLL as locked? "pll_lfvolt" stays...
Part Number: DAC3482 I wonder how to declare PLL locked. According to the datasheet, PLL alarm(REG5) does not work properly for ID 100b or any earlier. That is my case. Alternatively as recommended,...
View ArticleForum Post: ADS1220: Power up sequence of AVDD and DVDD
Part Number: ADS1220 Hi, We have one sensor which is powered through a LDO regulator, it's a battery powered device and the regulator must be shut down while not measuring in order to save power The...
View ArticleForum Post: ADS1292: ADS1292 chip's pad lands connection
Part Number: ADS1292 Dear Engineers, There is a question about ADS1292 chip's pad lands connection. I wonder whether it's connected to digital or analog ground. Looking forward to your reply. Thanks Robin
View ArticleForum Post: RE: DAC38J82EVM: Trouble locating software to configure the DAC...
I have installed the GUI. Thank you.
View ArticleForum Post: ADS805: What is the Convert Clock Period
Part Number: ADS805 I am also looking at using Texas Instruments ADS805 on page 4 of the datasheet there is a table that states Tconv Min =50, Max =100us and ns not sure if this value is us or ns
View ArticleForum Post: DDC114: Anti-aliasing Filter
Part Number: DDC114 Hi Team, Is an anti-alias filter necessary for the DDC114 in the case of frequencies above the Nyquist limit? I assume with a max sample rate of 3.125khz that if there are faster...
View ArticleForum Post: ADS1299: Bias Lead Off Detection At Power-up
Part Number: ADS1299 Hi, I want to use this feature on the ADS1299 evaluation kit. I can't get it to work constantly. What are the steps and the register involved to activate this feature correctly ?...
View ArticleForum Post: RE: ADS1278-EP: Device driver of MMB0 for Windows 7 or XP
Dear Christian: Thank you very much for your help. It still didn't work after I removed the old installation and installed the newly-downloaded ADCPRO-installer.exe. Here is something interesting....
View ArticleForum Post: RE: ADS1278-EP: Device driver of MMB0 for Windows 7 or XP
Hi Wenquan, Did you install the ADS1278 plugin? The MMB0 will be installed with the plugin. As far as the adcpro-launcher, that program has not been used for some time, but unfortunately the user's...
View Article