Forum Post: RE: TSC2200: system restart when pressing key
Hello Xuewen, We have looked through your document and are not immediately sure about the behavior. Please note that support for these devices is limited and we will look into the information we have...
View ArticleForum Post: RE: AFE4403: Output of Receiver Front End in case of input signal...
Hi Prabin-san, Thank you so much for your reply. I undrstood. But let me check the meaning about the datasheet description page 84 as below. There is a following description about AGC, Does this mean...
View ArticleForum Post: RE: ADS1292R: Common mode voltage
Then, PDB_RLD bit also must be set to 0 for mid-supply voltage?
View ArticleForum Post: RE: ADS8588H: Low frequency conversion
Thank you very much for your response, So you think that there is not any problem with the device at low frequency (0.5Hz)? , just because of the bins, huge samples are needed to calculate AC...
View ArticleForum Post: ADS8688EVM-PDK: WIN10 driver issue
Part Number: ADS8688EVM-PDK Hi, I met the same driver issue as below link on win10. please share the WIN10 version driver to me. thanks.
View ArticleForum Post: RE: TSC2200: system restart when pressing key
thanks, by the way, we used MAXIM MAX1233 before, the signal of row and column is better when key is pressed. we change to use TSC2200I because MAX1233 is end of life.
View ArticleForum Post: RE: ASLKPRO: ASLKPRO
Hi Upendra, I am sure following reply will help you. On ASLK Pro, the multiplier is MPY634KP which has a reference of 10V. So if you are applying two input signals V1 and V2 to this multiplier the...
View ArticleForum Post: RE: ADS122C04: Measuring voltage reference to ground
HI Bob, Below some additional information. Please, let me know if I missed something useful. 1) I am not measuring a thermistor. I have to trace the VI curve of a non linear device in the range -15 /...
View ArticleForum Post: RE: ADS122U04EVM: Possible to communicate via COM-Port
Hey Bob, i've taken a pciture of the situation the usb-cables are connected to my pc. Ifi try to get an conversation in this state, i receive no answer from ads. If i remove the jumpercable at jp1, it...
View ArticleForum Post: RE: ADS1292: Using the ADS1292 without RLD electrode
HI Ryan, This is highly appreciated. If I can contribute in some way please let me know. Kind regards,
View ArticleForum Post: RE: ADS1255: Using one crystal / voltage reference for multiple...
Hi Chris, I will use 1 LDO for the ADCs. Can you recommend one to power all the ADCs? I read on the DAC8532 data sheet that i could use a REF5050 for supply and reference. I like this solution but...
View ArticleForum Post: RE: TSW14J56EVM: DAC3XJ8X+TSW14J56EVM (how to load external...
We are looking into it.
View ArticleForum Post: LMP90100: Great Disturbances on some channels of the LMP90100 at...
Part Number: LMP90100 Hello! We are using the LMP90100 in our precision pressure measuring instrument. Three pressure sensors are connected on three differential channels of the LMP90100 respectivly....
View ArticleForum Post: RE: ADS1298: 1 bit shifted received from AD1298 with MSP430F67651A
Hello Ryan, I have checked the waveform and it is same as ADS1298 side. i dont know why it is little higher than 3.3V but i am supplying 3.3V exect to the controller. also when i read registers from...
View ArticleForum Post: RE: DAC34SH84EVM: FTDI pattern generator setting
I installed a 32-bit LabVIEW on a 64bit Windows. The program can run without error pop up. Now I wonder if it is possible to load the registers from the TSW308x GUI directly? It is not easy to make my...
View ArticleForum Post: DAC38RF83: Power Amplifier Protection Ideal Settings
Part Number: DAC38RF83 Hello Team, can you provide some guidelines how to configure the PAP settings, please? Thanks and Best Regards, Hans
View ArticleForum Post: RE: DAC38RF83: Power Amplifier Protection Ideal Settings
Hi Hans, One of our device experts will be back with you shortly. Best Regards, Dan
View ArticleForum Post: AFE7225: AFE7225 software tool "AFE722X EVM Software Control"
Part Number: AFE7225 Hi All, From where can i get or install the user GUI "AFE722X EVM Software Control" associated with AFE7225EVM board that demonstrates the configuration settings needed for the...
View ArticleForum Post: DAC38RF80EVM: NCOs Operation Levels
Part Number: DAC38RF80EVM Hey all, So after receiving previous direction on how to test the NCOs and subsequent output of the DAC before interfacing with the FPGA(see: e2e.ti.com/.../776799) , I began...
View ArticleForum Post: RE: DAC8831EVM: DAC8831EVM
Hi, I don't succeed using DAC8830 or DAC8831 without nLDAC. I have always had the same signals, fully corrupted. It's a problem because i have to use the DAC8830 (so without the nLDAC signal). To...
View Article