Forum Post: RE: Questions about TX-SDK-V2 EVB
Hi Valeri,Since you are using the TX-SDK-V2, which has LM96550 High Voltage Pulser, you would be needing an external bench supply of +/- 40V to the pins VPF & VNF.I apologize for the information...
View ArticleForum Post: RE: Questions about TX-SDK-V2 EVB
Hi Valeriy,I wouldn't recommend you to use a voltage divider to generate the +/-40V. You have to build a completely separate power supply for +/-40V. Depending on your operating frequency and mode,...
View ArticleForum Post: Software/Disc for TX-SDK-V2/NOPB?
I just received a TX-SDK-V2/NOPB and the GUI software disc was missing. Does anyone have an ISO or can it be downloaded anywhere online?Any help/advice is greatly appreciated!
View ArticleForum Post: RE: AFE0064 output current
Hi Iolanda,On the failure: The AFE0064 will not get damaged as long as the input voltage at the pins are within the Abs max ratings mentioned in the datasheet. Also, try to limit the current onto any...
View ArticleForum Post: RE: functioning of LM 96570
Hi Mariusz,Would you please send me(06jxlwsw@zju.edu.cn) a copy of your app for calculating beamform? And it will never be used for any commercial purpose!Thank you so much!
View ArticleForum Post: RE: functioning of LM 96570
Hi Shiwei,No problem, I will send you the software within a few minutes. Anyway, you can use it free also for commercial purposes. I'll be glad if it could be somehow helpfull.Regards,Mariusz
View ArticleForum Post: Software/Disc for TX-SDK-V1?
Hi, I am davinciJ. There is no driver and software in TX-SDK-V1 EVM kit.And the TI sales said pass a link to download,but not yet recieve.Could you help me to deal with this problem?My Email...
View ArticleForum Post: About TX-SDK-V1 powersupply?
Hi, I have a question about powersupply.There +/- 50V , +/-10V , +/-5 , +/- 3.3 , sub and with ground on the TX-SDK-V1 kit.Could you tell me what is using for by different Voltage ?? And is it turn...
View ArticleForum Post: RE: AFE0064 output current
Hi Nagesh,thank you for your reply. Taking in account point 1 and 2 the linearity is ok. I am aware of the DDC264 and I am already using the evaluation board; only problem is that we do not have a...
View ArticleForum Post: RE: LM96551
Hi Grzesiek,1) When the IC is overheated, the OTP pin goes low. One can tie the OTP to the EN pin to disable the pulser. The VSUB current can be as high as 30mA (CW mode, all 8 channels on, 500pF...
View ArticleForum Post: RE: About TX-SDK-V1 powersupply?
Hi Charles, Thanks for your answer,It's really very import for me~Thanks again.Wrong power will burn the Board.May I ask more detail??The +/-50V, +/-10V, 3.3V & sub are used by the LM96551...
View ArticleClik here to view.
Forum Post: Need Help for Ultrasonic Imaging Applications of...
Hi, everyone. I recently use a set of TI product for ultrasonic imaging. Here are several problem that I have met. Really Need your help T_T !Q1: I have already read Mariusz’s post...
View ArticleForum Post: RE: LM96551
Hi Grzesiek,When MODE is set to HI, only one set of outputs are active. When MODE is set to LO, two sets of outputs are active. You can probe the MODE pin to make sure when you set MODE to HI, it's HI...
View ArticleForum Post: RE: Software/Disc for TX-SDK-V2/NOPB?
I just received a TX-SDK-V2/NOPB without the GUI software disc. Where can I download the GUI software and userdocumentation?Thanks,
View ArticleForum Post: RE: Need Help for Ultrasonic Imaging Applications of...
Hi Shiwei,Q2: You can use the LM96551 to reduce the number of supply by two. It has build in LDOs for the +/-40V.Q3: When you use CW mode, you need to lower the VPP & VNN supplies to +/-5V or so....
View ArticleForum Post: RE: About TX-SDK-V1 powersupply?
Hi Fu-Sheng,The documentation is back in the web now. Sorry for the inconvenience. I attach a slide of the lab bench power supply setup for the TX_SDK_V1 that my coworker did. If you have further...
View ArticleForum Post: RE: Software/Disc for TX-SDK-V2/NOPB?
Hi All,Please download the software @ http://www.ti.com/tool/tx-sdk-v1Regards,Charles
View ArticleForum Post: DRV201YMBR
Hello,we are using the voice coil motor (VCM),we intend to change the direction of the motor using driver, the part number of driver is "DRV201YMBR" , So please do inform is it possible to change the...
View ArticleForum Post: RE: About TX-SDK-V1 powersupply?
Hi Charles, I am very very thanks for your help. The power supply information is got by your document.I will try to setup .Thank you so much again.Have a good time.Fu-sheng
View ArticleClik here to view.
Forum Post: RE: Need Help for Ultrasonic Imaging Applications of...
Hi Charles,Thanks for your patient reply!For Q2: Is the package of LM96551 compatiable with LM96550 so that I can replace it right now.For Q3: I notice such description in page 8 of LM96550 data...
View Article