Forum Post: RE: CCS/DAC8760: Example Code For DAC8760
Hi, My colleague will get back to you after the weekend. Thanks, Paul
View ArticleForum Post: RE: AFE5801: is there any length matching requirements for the...
Hi Tarang, How are you? Thank you for using AFE5801 device. For your question #1: Ideally the length matching for Analog Input Signals need to be totally matched from one channel to the other channel....
View ArticleForum Post: RE: ADS4126: ADS4126 Serial Interface Issues
Shim, Did you set the READOUT register bit 0 to a "1" in address 0x00? You must do this for the serial read back. Otherwise the pin will be set to report OVR. Also register 42h bit 3 "DIS LOW LATENCY"...
View ArticleForum Post: RE: DAC80504: DAC output configuration
Hi, Please note that the DIV=1 GAIN=1 is not valid! I had long time in the lab until I've understand that this combination is NOT WORKING e.g. outputs are ZERO! Noam
View ArticleForum Post: RE: Xilinx KCU105 with HSDC Pro - Error
Yes. I did what you mentioned. That is when I get this error. I tried in two different computers one with Win 7 and one Win 10. In both the cases the error was the same.
View ArticleForum Post: RE: ADS1232 unwanted internal offset
Thanks Bob, I will develop a new layout.
View ArticleForum Post: RE: DAC34H84: Deferent the Ouput Delay both 4 Chenel.
hello I wait your feedback. Please Check the My question. Regards.
View ArticleForum Post: RE: ADS8688: daisy-chain only works with up to 8 ics
Hello Eva, I apologized for late response, and pasted days were holiday in US. Please notice that higher number ADS8688 devices than FOUR in daisy-chain will lead to timing errors as mentioned in...
View ArticleForum Post: RE: DAC80501: RTM schedule
Hi Pol, I am checking with the team. I should be able to get an answer by tomorrow. Regards, Uttam Sahu Applications Engineer, Precision DACs
View ArticleForum Post: DAC8734: DAC 8734 READ
Part Number: DAC8734 *DAC 8734 READ Questions* 1.Voltage on DAC 8734 READ ->The voltage used for DAC control is (DVDD (+ 5v) / IOVDD (+ 3.3v) / AVDD1,2 (VDD + 15v) / AVSS1,2 (-15v)).Of the four...
View ArticleForum Post: LM98725: Question about sampling mode
Part Number: LM98725 Hello I used LM98725 with Sony CCD ILX901K (S/H output). Recently, the Sony CCD was discontinued and changed to Toshiba CCD TCD2717BFG (CDS Output) The output voltages of the two...
View ArticleForum Post: RE: AFE4420: Data output is not correct in rare case.
Hi Ryoji, Since AFE4420 is shared under NDA, let's take this discussion offline. You can email me regarding this. Regards, Prabin
View ArticleForum Post: RE: AFE4490: HOW CAN I ENABLE LED_ALM AND PD_ALM ON AFE4490
Hi Cesar, You have to enable the diagnostics by setting DIAG_EN bit. Once enabled the AFE does the checks and gives the output on Flags as well as on LED_ALM and PD-ALM pins. So you can observes those...
View ArticleForum Post: RE: DAC38J84: DAC38J84EVM + TSW14J10EVM + ZC706 issue
Hello thanks for your suggestions i tried using TCL script to build the project in vivado TCL console, the problem is,i am currently using vivado 2018.2 and the given example on TI`s webpage support...
View ArticleForum Post: Compiler/ADS1294R: LOFF register voltage mode and current mode...
Part Number: ADS1294R Tool/software: TI C/C++ Compiler Dear Friends I have configured register LOFF as a current mode so I get the ECG waveforms but I changed pullup or pulldown resistor mode in LOFF...
View ArticleForum Post: Compiler/ADS1294R: LOFF register voltage mode and current mode...
Part Number: ADS1294R Tool/software: TI C/C++ Compiler Dear Friends I have configured register LOFF as a current mode so I get the ECG waveforms but I changed pullup or pulldown resistor mode in LOFF...
View ArticleForum Post: RE: DAC5652A: When in Power-down mode (not ZERO)
Hello Neeraj, Because the customer can not try your idea immediately. Could you give them the waveform that result of applying your idea? They have one more question. Is there any limitation of the...
View ArticleForum Post: RE: DAC8742H: HART modem FIFO does not clear characters.
OK, here's an update. Whatever command I clock in the reply to the previous command is clocked out. That's why it appeared that MODEM_STATUS_REG and FIFO_M2D addresses appeared to be backward. So, what...
View ArticleForum Post: RE: DAC38J84: DAC38J84EVM + TSW14J10EVM + ZC706 issue
Hi thank again for prompt reply. i have another question, keeping this in mind, i have the same set up of hardware so is there any solution for generating customized/ arbitrary waveforms on 4 DAC...
View Article