Forum Post: RE: ADS7945: Remarkably good transition noise specification?
Hi Tony, Sorry for the delay here. The transition noise on the ADS7945 is correct, no typo. We don't have final numbers for the ADS9224R yet, they will be published as soon as they are verified.
View ArticleForum Post: DAC38RF89: DAC38RF89 LMFSHD = 42111 (dual independent DACs with...
Part Number: DAC38RF89 Currently experiencing what appears to be a delay offset between I and Q data (potentially a delay difference on a lane basis i.e. individual bytes). I can't tell from the...
View ArticleForum Post: RE: ADC121S021: Software compatibility of ADS12XS021 series
Hi Tom-san, Thanks, I understood that. Regards, Takashi Onawa
View ArticleForum Post: RE: ADS124S06: Conversion to be output "Unsigned" character
Hi Joachim-san, Thanks for you prompt response, and I understood that. The customer could convert the data by their selves, so I will close this thread soon. Regards, Takashi Onawa
View ArticleForum Post: RE: BOOSTXL-ADS1219: ADS1219
Hi Mark, I tried my best to get this uploaded today, but I didn't make it. I will attempt again tomorrow. Sorry, Bob B
View ArticleForum Post: ADS8688: question about TI design (TIDU365B)
Part Number: ADS8688 Dear expert, We found a TI design - TIDU365B, which is similar with our application. But here are some question about schematic and BoM. 1. What's the function about TLP3123? 2.Why...
View ArticleForum Post: ADS1248: ADS1248 reaction caused by missing of SPI SLCK/DIN
Part Number: ADS1248 Dear Sir, It is not a trouble but system error case study. A customer test ADS1248 reaction at a case when SCLK and DIN are missing during a normal operation. What status ADS1248...
View ArticleForum Post: RE: ADS8688: question about TI design (TIDU365B)
Hi Ben, This reference design can measure voltage or current signal. When the input is current signal(4-20mA or 0-20mA), the host controller commands TCA6408A to turn on or off the 200ohm resistor,...
View ArticleForum Post: ADS54J20EVM: ADS54J20
Part Number: ADS54J20EVM Hi Team, We observed that in the ADS54J** EVK, the terminations used for the analog signals is made as shown below for INAP, INAN, INBP and INBN signals: In the datasheet of...
View ArticleForum Post: RE: ADS1232: ADC count variation
Hi Bob, Can you please share your Email ID so that I can share the PCB files with you. Thanks, Sreekanth
View ArticleForum Post: RE: TLA2024: I2C communication is failed
Hello I confirmed the operation with ADS7823 - 28EVM. The result was no problem. Thank you very much.
View ArticleForum Post: RE: ADS7852: ADS7852YB/250
Can you please clear me that this LTC code is valid or not. And this part is TI's genuine part.
View ArticleForum Post: ADS1230: make low cost Weigh Scale
Part Number: ADS1230 hi friends i just think to make a low cost weigh scale with ads1230 with cc3220 please clear my doubts 1.it's Communicate with SPI Communication. is it possible to get ADC output...
View ArticleForum Post: ADS1293: ADS1293 3-Lead ECG noise
Part Number: ADS1293 Hi Sir Please refer below picture. (schematics & waveform) According application note SBAA188 ( Improving Common-Mode Rejection Using the Right-Leg Drive Amplifier ) figure 7...
View ArticleForum Post: TINA/Spice/ADS8688: the simulation model doesn't contain the spi...
Part Number: ADS8688 Tool/software: TINA-TI or Spice Models hello, the Tina model for the ADS8688 doesn't contain the spi interface is it possible to get the reference for a similar component that does...
View ArticleForum Post: RE: DAC38RF89: DAC38RF89 LMFSHD = 42111 (dual independent DACs...
I have reviewed the software and it is implementing figure 141. We are using mixer + NCOs and have synchronized after writing to the NCO frequency word (even changed the sync methods). I need to verify...
View ArticleForum Post: ADS1262: ADC1 Noise
Part Number: ADS1262 Hello, Our customer use the ADS1262 , have a question. There is the Table 1 on the datasheet. How was this data obtained? Is it a characterization data? or simulation results? Best...
View ArticleForum Post: ADC32RF45: adc32rf45 GUI Setting?
Part Number: ADC32RF45 Dears. When setting " ADC32RF80 _LMF_8411" in GUI, Disable B channel. Then, is it correct to operate with L = 8, M = 4 for A channel? Does it work in the following format? M0 = A...
View Article