Forum Post: ADS54J40: ADS54J40 Latency
Part Number: ADS54J40 Dears. What is the way to reduce latency in the ADS54J40 ? What is the fast way to do JESD204B Link? We are used Altera Arria 10. Thank you
View ArticleForum Post: RE: ADS52J90: Road map
Hi Chen, How is the progress about this request? Best regards, Shimizu
View ArticleForum Post: RE: ADS8634: Aging drift of accuracy
Hello TQ, I apologized for the delay. We do not have long term drift data for the reference on this device after checked. Best regards Dale
View ArticleForum Post: ADS1262: ADS126XEVM-PDK-SW
Part Number: ADS1262 Dear, Support Team. My customer is going to evaluate ADS126XEVM-PDK-SW. Is ADS126XEVM-PDK-SW with Windows 10 operating systems support? Best Regards, Hiroaki Yuyama
View ArticleForum Post: RE: Design Low cost Weighing Scale
Hi Bob B Thanks for your reply 1.this is my first project with Ti 2. I have cc3220 Evaluation Board I don't know how to Program this and how to connect with ADS1230 . Before that i was work with some...
View ArticleForum Post: ADC12DJ2700EVM: ADC12DJ2700EVM
Part Number: ADC12DJ2700EVM I want to capture signals using the ADC12DJ2700EVM board and ZC706. However, the ZC706 board only contains FMC HPC and LPC but the ADC12DJ2700EVM has FMC+ HPC. Can I connect...
View ArticleForum Post: RE: ADS8688: question about TI design (TIDU365B)
Hi Dale, Thanks for your feedback. May I learn from you how to choose the optocoupler? Or we have to design with TLP3123 because it have something special feature? -Ben
View ArticleForum Post: AFE4490: Maximum frequency support and frequency divider register...
Part Number: AFE4490 Hi Sir/Mam, I am using AFE4490 IC pls may I know what is the maximum frequency support? And what is the register in AFE4490 for frequency dividing to get 4Mhz? present my design I...
View ArticleForum Post: AFE5808A: AFE5808A FFT Spectrum problem when system inputs are...
Part Number: AFE5808A Hi there, We met similar problem as this thread : Our setup is similar to the orignial thread. We have 64 hardware channels, with 1:2 HV switched to 128 Piezoelectric crystals...
View ArticleForum Post: DAC101C085: I2C adress of right side
Part Number: DAC101C085 Hi, Team, My customer is using DAC101C085 (6 pin) and the customer reported that the right side slave address of Table 1 doesn't work. Is this correct behavior? Best Regards,...
View ArticleForum Post: RE: DAC38J84: DAC38J84EVM + TSW14J10EVM + ZC706 issue
Hi Kang thanks for your suggestions i am using HSDC PRO software to generate custom waveforms, now my question is how to set maximum sample rate of 2.5 GSPS at all four DAC of DA38J84EVM . because i...
View ArticleForum Post: RE: DAC161P997: DAC161P997 Output Problem
i did lots of modifications. As i said it works. please just check my codes at 3rd comment of this topic
View ArticleForum Post: RE: ADS131E08S: Channel offset calibration procedure doubts
Hello Ryan, thank you for your help. Everything seems to be clear now :) Have a good day! Best regards, Wojciech Kidula
View ArticleForum Post: AFE5808A: AFE5808A Thermal Protection question
Part Number: AFE5808A Hi there, I have to repeat this question. Datasheet section 9.3.6 requires user to make sure junction temperature below 105 degree by using heat removal technique. Is there...
View ArticleForum Post: JESD204B
hi, I was watching video about Three-part JESD204B training series. And the address is https://training.ti.com/zh-tw/JESD204Bpart1?cu=993610 . And I didn't see the PPT for downloading on the web. Can...
View ArticleForum Post: RE: High precision signal path with digital post correction
Hi Collin, Yes I can agree that static parameters will stay constant in the frequency range of interest (0-50Hz). However it bothers me how to quantify spectral purity of the system, distortion level...
View ArticleForum Post: RE: DAC38RF89: Confirming ILA_CFG
Hi Randhir, Since this is not related to the original post this tread was created, it is better to start a new thread so that this one does not grow too long. Also, this recent post looks similar to...
View ArticleForum Post: RE: TINA / Spice / DAC0800: Spice model for legacy devices
hi,Kevin thanks for answer and information,i have contact with Design Software but for the present don't receive answer i don't understand,can i order SPICE model at TI Best regards
View ArticleForum Post: RE: ADS61B29: Questions about trace lengths and proper...
Hi Carolus, 1. From datasheet Page 4, the volatge at the analog input pins should never go below -0.3V or above min(3.6V, AVDD+0.3) 2. The ADC will saturate if you exceed the 2Vpp Full scale...
View Article