Forum Post: RE: DAC161P997: DAC161P997 Breaks down without reason
Is amy multimeter cause this ? Like difference Rloads. I an consuming dac161s like candy
View ArticleForum Post: RE: DAC101C085: I2C adress of right side
Hi, Uttam, Thanks for the reply for this. We recommended to use the primary set of I2C addresses. Best Regards, Satoshi Yone
View ArticleForum Post: AFE5809: AFE5809
Part Number: AFE5809 I am trying to capture data using AFE5809EVAL with TSW1400 using the two GUI's provided by TI along with these boards. For the default configuration sampling frequency is 40MHz....
View ArticleForum Post: RE: DAC101C085: I2C adress of right side
Hi Satoshi, Thanks for the confirmation. I am closing this thread. You can reopen it in case you have any further questions on the same topic. Regards, Uttam
View ArticleForum Post: RE: TINA/Spice/ADS1298: ADS1298
Ch2 Ch3 Ch4 Ch5 Ch6 ch7 ch8 ch1 Dear Alex, Again thank you for your valuable feedback. To make sure all of your comments:set CLKSEL =1, does the oscillator correctly wake up? Does /DRDY toggle? Do you...
View ArticleForum Post: RE: ADS1293: ADS1293 3-Lead ECG noise
Hi Alexander As below waveform is using patient simulator & output sine wave for you refer. 1. lead-off (disable) 2.lead-off (8nA) About your recommend RC filter for electrode inputs . May I refer...
View ArticleForum Post: RE: ADS8681: ADS8681
Hi Siva, Can you tell us what part of the ADS8681 datasheet is confusing you, or perhaps provide details on how you are communicating with the ADS8681 (data you send and then receive), perhaps adding...
View ArticleForum Post: RE: ADS8555: About reading control register
Hi DDdoor, Can you be a little more specific on what commands you are sending to the ADS8555 ?
View ArticleForum Post: ADS1278-EP: information about MMB0 modular EVM motherboad of...
Part Number: ADS1278-EP Hi, I bought ADS1278 EVM board and under testing. I,m going to implement TDM communication. So can you send me the schematic and software of MMB0 modular EVM motherboard? thanks...
View ArticleForum Post: RE: AFE5809: Questions about AFE5809 CLOCKs
Hi Yi, Hope this blog could help you. how-to-measure-additive-jitter-of-a-clock-buffer Best Regards, Shawn
View ArticleForum Post: RE: AFE4300: inconsistencies in bcm adc
Should it be done each day? Does ADC value for known resistances vary each time in afe?
View ArticleForum Post: RE: ADC12J4000EVM: JESD204B output data of ADC12J4000
Hello, Concerning our "proper K_symbols on ILAS data", I inform more details of captured ILAS pattern. I attach the whole ILAS data below, The position of K seems to be correct to JESD204B_5.3.3.5. [...
View ArticleForum Post: TPL0102-100: Write protect
Part Number: TPL0102-100 Hello, Our customer use the TPL0102, have a question. Does the TPL0102 have register write protect ? Best Regards, Naoki Aoyama
View ArticleForum Post: ADS8900B: What is the use of pattern registers?
Part Number: ADS8900B Hi TI Team, Can you please help me to understand what is the pattern mentioned through DATA_CNTL, DATA_VAL, PATN_LSB, PATN_MID and PATN_MSB? Please explain me with small and quick...
View ArticleForum Post: RE: ADS1115: Problem when working in single shot mode using...
Artem, The ALERT/RDY state doesn't change with a read of the device, the ALERT/RDY only goes low at the completion of a conversion. Joseph Wu
View ArticleForum Post: ADS8900B: SPI interface compatibility with Xilinx AXI Quad SPI IP
Part Number: ADS8900B Hi All, I am developing a design where i use ADS8900B to monitor the current supplied to one of the module on the board. I want to use "Xilinx AXI quad SPI IP" in master mode to...
View ArticleForum Post: ADS1261: IDAC specification
Part Number: ADS1261 Dear Technical Support Team, I have some questoins about IDAC specification of ADS1261 . ① Is it correct understanding about Accuracy and Same Current magnitude below? The current...
View ArticleForum Post: RE: ADS4245-EP: ADS4245-EP clkout is not proper
With this inputs can we confirm that ADC is not functioning, as CLKOUT is not proper. Shall I go for replacing the ADC chip. Any other point to check which may confirm that ADC is not functioning...
View ArticleForum Post: ADS8350: VOL with external pull-up
Part Number: ADS8350 Hello, I have a question for ADS8350 VOL specification. Now I have to add external pull-up on SDO-x line for some reason. Then I want to understand acceptable pull-up resister...
View Article