Forum Post: RE: ADS1235EVM: Firmware recovery.
Hi Christopher! Thank you for your replay. I`ve installed LMFLASHPROGRAMMER , but when I check the folder "C:\Users\ \Documents\DSEvalSW\ there is the only folder inside "Logs". Additional information:...
View ArticleForum Post: RE: CCS/ADS8699: ADS8699 SPI DMA example c code
Hi there, Unfortunately, we don't have any example code for the ADS8699 with the MSP430P401R to share with you. However, I see that you've been asking similar questions on the MSP430 forum and it...
View ArticleForum Post: RE: ADS1118: ADS1118 EVM Configurations Problem
Hi Wayne, Just curious, but if you disable 'Auto-Write' and press the 'Write Config Reg' button in the ADS1118 GUI, does it make a difference in the read? Writing 0x086 B should get you the...
View ArticleForum Post: RE: ADC122S655: how about the adc122s655 out data?
Hi David, Welcome to our e2e forum! The ADC122S655 is a 2 channel simultaneous sampling ADC, both channels come out on the single SDO pin of the device as shown in Figures 1 and 2 in the datasheet. The...
View ArticleForum Post: RE: CCS/ADS8699: ADS8699 SPI DMA example c code
Hi, thank you for writing. CS is low I recognised. I wired it as you can see in the code. At first i want to test directly with SPI, later with SPI with DMA because its more complicated. From the...
View ArticleForum Post: ADS1278: SPI Code Example
Part Number: ADS1278 Could someone please email me source code for reading from the ADS1278 over an SPI bus on an Arduino? Similar to how the following user was emailed source code:...
View ArticleForum Post: ADS1220: ADC resolution and sampling rate
Part Number: ADS1220 Hello, I want to ask following question: I have requirements of having a SPS at >=300 SPS. If i choose PGA = 1 and SPS = 330, I can expect 17.7 ENOB as written in the data...
View ArticleForum Post: ADS8555: About reading control register
Part Number: ADS8555 Hello,Dale Below is the situation of the customer. >1. Can the customer get the correct out data without any change Control Register (default value)? Since it is SPI, I think...
View ArticleForum Post: RE: ADS1282EVM-PDK: Trying to integrate the ADS1282 to a MCU and...
Hi Chris, I'd like you to know that we integrated it all and it worked properly: MCU + ADS1282 + Geophone. Thank you, wouldn't be possible without your help. Second thing: we decided to use the second...
View ArticleForum Post: RE: DAC38J84: DAC38J84EVM + TSW14J10EVM + ZC706 issue
Thanks Kang and Jim Now i am able to generate customized waveform . i have another issue i am generating .CSV file of 65536 samples in matlab. The array of samples looks like fine in matlab. but when i...
View ArticleForum Post: ADC32RF45: ADC32RF80 interleaving spur
Part Number: ADC32RF45 DEARS The ADC32RF80 is temperature tested. The temperature test range is -40 to 80 degrees How much is the difference in interleaving spur level due to temperature change?...
View ArticleForum Post: RE: ADS1263: Data rate is not as set ( for 38.4 KSPS data rate is...
I am using continuous conversion mode for single channel (AIN0 and ANI1), and I am reading samples by sending read command for every sample. When I am checking status byte for every sample for keeping...
View ArticleForum Post: RE: ADS8201: How to read ADC from ADS8201
Hi Tom, Finally, I find my issue. My Vref = 2.5V. So I just read adc value <= 2.5V I increase Vref to 3.3V. It's OKE. Thanks for your support Best Regards, Tam
View ArticleForum Post: RE: ADS1220: ADS1220 install issue
HI Bob I already Install the ADC PRO & ADS1220 Driver but, still show below figure when the EVB plug in, please advise it ,thanks
View ArticleForum Post: AFE4300: BCM Electrodes
Part Number: AFE4300 Hello, I am using stm with afe4300 . Can i know which electrodes are best/optimum to be used for bcm measurement? Thanks and Regards Abhinav Nagaraj
View ArticleForum Post: ADS7953EVM-PDK: Register addressing for SPI communication
Part Number: ADS7953EVM-PDK Hi Team, I want to interface this module with my main controller via SPI communication. The data sheet available on the website doesn't contain any information related to...
View ArticleForum Post: AFE4300: inconsistencies in bcm adc
Part Number: AFE4300 Hello, I am using afe4300 with stm for bcm and weight measurements. I am using the application circuit given in section 8.1.1 in afe datasheet on the page number 30. I am putting...
View ArticleForum Post: RE: AFE4300: inconsistencies in bcm adc
Just to avoid any confusion. I am using the application circuit in section 8.1.1 for bcm measurements only.
View ArticleForum Post: RE: ADS1230: ADS1230 Thermal resistance coefficient
OK.Look forward to your test results，thanks!
View ArticleForum Post: RE: ADS61B49: AVCC/AGND and DRVDD/DRGND
Hi Eben, Do you have any update so far? Thank you for your cooperation. Best Regards, ttd
View Article