Forum Post: RE: TINA/Spice/ADC12DL3200: SYSREF processing activity
Hi Jim, thanks for your analysis. In our project we don't use a repetitive SYSREF but only single pulses to calibrate the SYSREF window and to alignment the Strobe signals. In this case, we've verified...
View ArticleForum Post: ADS127L01EVM: AC and DC measurements
Part Number: ADS127L01EVM Hi, I have a question regarding the programming code of the evaluation board. When I use the demo software to merasure AC signals I could measure the AC signal above 10kHz but...
View ArticleForum Post: RE: DAC8742HEVM: Can I use some teraterm terminal to read...
Hi Garrett, Can I confirm the full HART frame you mean is like the below picture by sending HART message correctly, UART can receive HART response as you expected? Secondly, will UART have "hardware...
View ArticleForum Post: CCS/PGA900: Run of Firmware does only work when debugging but not...
Part Number: PGA900 Tool/software: Code Composer Studio Hello, I took the generic firmware of TI and changed it in a way, that it communicates via spi with my own gui. So now when I start my device...
View ArticleForum Post: RE: ADS1261: Full Scale Calibration
Hi Chris Hall, Thank you for your reply. Additional question, When â‘ G=1.1(just example) over 7FFFFF and issuing the GANCAL command, then ADS1261 compensate from â‘ G=1.1 to G=1.0 automatically? Based on...
View ArticleForum Post: DAC7731: What does the silk print on the package mean?
Part Number: DAC7731 Hi What does 88Z04MV on the package mean? Is there batch information? Thanks. Jerry
View ArticleForum Post: RE: ADS8568: Data not received. Parallel interface mode &...
Hi Dale, Our problem is resolved. The Error was in the initiation of the micro-controller port on which we are reading the ADC's paralled data. Your code helped us a lot in making our code more perfect...
View ArticleForum Post: RE: CCS/ADS131E08: STATUS REGISTER SHOWS HIGH FOR FAULT_STATN...
Hi Joseph, I even noticed that, the DRDY signal goes low at 32kHz frequency,though the DR is 1ksps or 32ksps. I think it should change. Can we infer that the CONFIG3,CONFIG1,CONFIG2 commandS are not...
View ArticleForum Post: RE: CCS/PGA900: Run of Firmware does only work when debugging but...
Hello Andreas, There are other considerations when you wish to have the program boot from flash on power up. They can vary from device to device. I will move your thread to the device forum. These...
View ArticleForum Post: ADS1258EVM-PDK: Driver for MMB0 Board
Part Number: ADS1258EVM-PDK Hello Forum, I tried to run with ADCPro the ADS1258-EVM, but the firmware said that the download failed. And from another thread I know I need the driver for the MMB0 Board,...
View ArticleForum Post: RE: DAC8831EVM: DAC8831EVM
resolved with driving nLDAC signal. So, DAC8831 doesn't work with nLDAC tied to GND. what happens with the DAC8830 ?
View ArticleForum Post: SM73201-ARC-EV: Compiling Error
Part Number: SM73201-ARC-EV Hi, It has compiling error in CCS 6.2.0.00050 as below picture. Where should I pay attention? Thanks.
View ArticleForum Post: TSC2200: system restart when pressing key
Part Number: TSC2200 please see the enclosed file for details(Please visit the site to view this file)
View ArticleForum Post: ADS1299: Drive shield with ADS1299
Part Number: ADS1299 Hi Folks, I would like to design an EEG system with ADS1299 , and I want to use DSUB connector for the electrodes, but the cable itself has only one shield for all of the inner...
View ArticleForum Post: RE: ADS1299: Sampling problem or SPI comunication? TEST Signal...
Hi Moises, How is testing going?
View ArticleForum Post: RE: ADS1294R: Bits Flickering in Lead Off registers
Hi Alex, Thanks for the documents and video which shared by you. I didn't observe like how to get Respiration Data from both RA-LA and RA-LL Combinations in ADS1298R at the same time. Could you discuss...
View ArticleForum Post: RE: ADS1294R: Bits Flickering in Lead Off registers
Hi Vignesh, Happy to help! As I mentioned in my previous post, unfortunately I am not familiar with deriving the respiration rate from the leads. As shown in the app note, our devices calculate...
View ArticleForum Post: RE: AFE5401-Q1: Trigger to DSYNC2 latency and digital output latency
Hi Chen, thank you for your answer! Regarding the second question: The way I understand it now is, that the digital output delay of setup 2 from above is ~420us, correct? These are the settings from...
View ArticleForum Post: RE: ADS1292: how to cancel the 50/60Hz noise without RLD lead
Dear Andrews So, increasing the resistor is better for input impedance but worse for CMRR? Another question : In other issues opened in this forum for no RLD lead, you suggest that driving IN1N, IN1P,...
View ArticleForum Post: ADS131A04: ADS131A04
Part Number: ADS131A04 Hello, I would like to know the settings need to be done in ADS131A04 to achieve data rate of 128ksps. Thank You Bushra
View Article