Forum Post: RE: Ultrasound Analog Front End With 204B interface
iehncent, Yes we have two AFEs (VCA +ADC): AFE58JD18 and AFE58JD16 and one ADC only part: ADS52J90 Chuck Smyth
View ArticleForum Post: AFE5816: Frequency of ADC_CLK and FCLK
Hi all, According to the datasheet of AFE5816 , FCLK is the same frequency with ADC_CLK. However my customer reported that the FCLK is a half of ADC_CLK, and 12bit length of the data to be output are...
View ArticleForum Post: AF5809 Coefficient SPI Programming
Hi, I'm having trouble configuring the AFE5809 decimation filter. I'm using the following coefficients take from a previous post for say decimation by 8 filter uint8 pu8_fircoeff_DEC8[8 * 14]={...
View ArticleForum Post: RE: AFE5816: Frequency of ADC_CLK and FCLK
Toshi, Please ensure that ADC Reg 1 [2] and [4] are both set to '1'. Thanks, Chuck
View ArticleForum Post: RE: Using LM98725
Hello Martin, This is a 3.3V part and the abs max voltage as shown in the datasheet is 4.2V, with current limited. Vih is 2V. I would recommend keeping the input voltages less than the supply voltage...
View ArticleForum Post: RE: LM98620 eval board schematic
Can Hooman or anyone else re-share the schematics for LM98620 evaluation board? Best regards.
View ArticleForum Post: RE: LM98620 eval board schematic
Hello, Here is the LM98620 EVM schematic and layout information: (Please visit the site to view this file) Note : The files containing "Des" in their file names are the des erializer portion connected...
View ArticleForum Post: Medical Ultrasonograpy SENSOR for LM96530/550/570 family....
Hello, I am looking for a ultrasonography transduder compatible with LM96530 /550/570 chips by TI. In other words this transducer must be compatible with TX-SDK-V2 Ultrasound TX Evaluation Kit My...
View ArticleForum Post: RE: Medical Ultrasonograpy SENSOR for LM96530/550/570 family....
Hi Vincenzo, I've moved this post from the Medical Forum to the Imaging AFEs Forum. I'm sure you'll find an answer here.
View ArticleForum Post: RE: LM98620 eval board schematic
Thank you very much Hooman, you are a lifesaver! I need to ask for the BOM file (I could not find it in the RAR file), and of course the SensorEval software. Thank you in advanced.
View ArticleForum Post: RE: LM98620 eval board schematic
Hi, I've added the two board BOM's to the original zip file (posted on July 25, 2016). The SensorEval software can be downloaded off the web here: Regards, Hooman
View ArticleForum Post: RE: LM98620 eval board schematic
Hello thank you Hooman I find it in the updated file. Best regards
View ArticleForum Post: TX SDK V1/V2
What is the difference between TX SDK V1/V2? Is the only difference that one uses the LM96551 and the other one the LM96550 ? The price difference of these boards is 200$. The LM96551 offers "floating...
View ArticleForum Post: RE: TX SDK V1/V2
Hello, Here is the difference between TX-SDK-V1 and TX-SDK-V2 : The difference between the TX-SDK-V1 and TX-SDK-V2 is the pulser. V1 is for the LM96551 , which has the floating supplies VPF and VNF...
View ArticleForum Post: RE: LM98620 eval board schematic
Hello, I've been told that there may be issues with using the SensorEval web installation file with the LM98620 (or LM98xxx devices in general). Here is the installation file (along with instructions)...
View ArticleForum Post: RE: LM98620 eval board schematic
Hello, Thank you again for your concern. I need to ask you about the Gerber files, can you share them? and if it possible to share the original schematic files in any format like (Eagle, Altium,...
View ArticleForum Post: RE: LM98620 eval board schematic
Hello, I'm sorry but I don't have the EVM Gerber files (*.gbr extension) or the source schematics. I will ask other colleagues available next week, and if I am able to locate these, I'll post them to...
View ArticleForum Post: RE: TLV990-13: specifications
Jason-san, Thanks a lot for your support. There are two additional questions about below specification. 1. What is the minimum CLCCD * pulse width? Is it the same with a pixel period? 2. Is there the...
View ArticleForum Post: TX-SDK-V2/NOPB
Hello, I'm working with TX-SDK-V2 /NOPB. At the experiment, unfortunately one of the 50 volt out put of the board got short circuit with ground( I was trying to see the output pulse by osiloscope...
View Article