Forum Post: RE: TX-SDK-V2/NOPB
Hi Parisa, Most likely, you'd need to rework / replace the Pulser ( LM96550 ) on the board. This is an 80 pin WQFN package. The following application note (SLUA271A) (section 6, Rework Guidelines) may...
View ArticleForum Post: RE: TX SDK V1/V2
Hello, Thank you very much for your reply. Now we bought the TX_SDK_V2. For the first tests we don’t need +/- 50V. Is it possible to configure J_SUB in the “1-2” position and to choose - -10 V for VSUB...
View ArticleForum Post: Ask for Layout
Hello TI, I'm working on ultrasound evaluation board by part number of TX-SDK-V2 . By the package there is a schematic of power module board but there is no lay out file. The schematic without layout...
View ArticleForum Post: RE: Ask for Layout
Hi Parisa, I've asked around and unfortunately we don't have the layout information to share with you. Regards, Hooman
View ArticleForum Post: RE: TX SDK V1/V2
Hi Biggik, I think you meant the following instead (shown in color ): - +/-10V for VPN VDD and VDN Yes, I think what you are proposing will work. Regards, Hooman
View ArticleForum Post: RE: TX SDK V1/V2
Hi Hooman, thank you very much for your reply! I took the VPN and VDN from the TX_SDK_V2 Users Guide chapter 2.3. But you are right it should be VDD and VDN. Maybe someone wants to correct it. Regards...
View ArticleForum Post: product
Hello TI, I'm working on Ultrasound evaluation board. But it damaged through doing some experience. I want to replace main ICs but those are unavailable and out of stock at both digikey and TI website....
View ArticleForum Post: RE: product
Hi Parisa, I'm asking around to find out what avenue(s) are available to you to get replacements for the LM96550 , LM96570 , and LM96530 . I'll post a response here as soon as I find out. Regards, Hooman
View ArticleForum Post: RE: product
Hi Parisa, I found that you can order it from this website: Regards, Hooman
View ArticleForum Post: RE: Need help in using TX_SDK_V1
I'm already designed power module to supply for this board.
View ArticleForum Post: Clock input to CIS sensor from LM98722 AFE's CCD timing generation
Hi, I am using Contact image sensor in my application, I am using LM98722 AFE to interface CIS sensor, i need help in CCD timing generation in LM98722 for providing clock signals to my CIS sensor.. I...
View ArticleForum Post: RE: TLV990-13: specifications
1. What is the minimum CLCCD * pulse width? Is it the same with a pixel period? Yes 1 or more. (recommend more than 1) 2. Is there the power on sequence between AVDD and DVDD? Current status of my...
View ArticleForum Post: RE: Clock input to CIS sensor from LM98722 AFE's CCD timing...
Hi Gokuleswaran, We'd need to see the timing diagram of the clocks you need for the CIS to see if the LM98722 is capable of generating them. Can you provide that? Regards, Hooman
View ArticleForum Post: RE: TLV990-13: specifications
Hi Jason-san, thanks for you reply. I have an additional question. What is the maximum CLCCD* pulse width? Is it less than BLKG* pulse width? Best regards, Toshi
View ArticleForum Post: RE: Clock input to CIS sensor from LM98722 AFE's CCD timing...
Hi Hooman, Thanks for your Reply, As for the information required for you, i have attached the timing diagram for your reference. Note: Clock Frequency – 4 MHz Clock Duty Cycle – 50% Data Output Timing...
View ArticleForum Post: RE: Clock input to CIS sensor from LM98722 AFE's CCD timing...
Hi Gokuleswaran, I got the following details for your specific timing requirement from another colleague and I've copied it below. See the programming sequence in Section 7.5.1, along with Table 6 and...
View ArticleForum Post: RE: Clock input to CIS sensor from LM98722 AFE's CCD timing...
Hi Hooman, Thanks for the information, I hope this information help us great to continue with our task, and once we achieved the output I ll intimate you. Thanks Again...... Regards, Gokuleswaran R
View ArticleForum Post: XEM3001 to TX-SDK-V2
MY question is, If i am going to program a controller in XEM3001 FPGA, then how to configure the pins in TX-SDK-V2 side? Is there any datasheets are available for tx-sdk-v2 board?
View ArticleForum Post: RE: XEM3001 to TX-SDK-V2
Hi Subash, The Opal Kelly module (XEM3001) is used to command the LM96570 through its 4-wire serial interface. The kit is already configured to do this and to enable operator control through the GUI on...
View ArticleForum Post: RE: LM98640 weird behavior
Hi, Even if VCLP is not necessary in CDS mode, can it still be connected to OS+ ? I am intending of using the LM98640 in a configuration were both S/H mode and CDS can be used. For instance, I would...
View Article