Forum Post: Recovering AFE channel compression
Hi folks, I'm working on a design with an AFE module where I'll be taking advantage of channel compression so that I'll have multiple channels multiplexed onto a single LVDS lane. I'll also be using...
View ArticleForum Post: RE: Pulse Patterns from TX-SDK-V2
Dear Smyth We look after drivers for ultrasound application (frequency near 50 kHz) TX734 (phased-out?) could run on this particular application but not TX517 due its BGA-144 pack If you please be so...
View ArticleForum Post: RE: Pulse Patterns from TX-SDK-V2
Silvio, Yes, TX734 was phased out and at this time our team only has the TX517 transmitter and TX810 T/R Switch. Otherwise, I would have to suggest TX-SDK-V1 parts. Chuck
View ArticleForum Post: RE: Pulse Patterns from TX-SDK-V2
Dear Smtyh Thank you for being polite and professional We go to internally discuss about your suggestive TX517 Kind Regards,
View ArticleForum Post: TLV990: Minimum Input ADCCLK frequency
Hi all, Could you tell me the minimum input ADCCLK frequency of TLV990? My customer plans to use this device at 4MHz. Regards, Toshi
View ArticleForum Post: code for ultrasound evaluation board
Hello TI support, This is Parisa. We bought the TX-SDK-V2 evaluation board for ultrasound transmitter in order to do some measurement. In this level we need to program the Opal Kelly EXM3001 FPGA...
View ArticleForum Post: RE: code for ultrasound evaluation board
Hi Parisa, Unfortunately we don't have anything to provide to you regarding the Opal Kelly module programming. Hopefully you've already looked at the Opal Kelly website: www.opalkelly.com/.../ Have you...
View ArticleForum Post: TI Ultradsound Transmit Solutions\ Opal Kelly \ TX_SDK_V1
I have built the Ultrsound transmit solutions( refence to http://www.ti.com/tool/TX-SDK-V1 Need I configure the Opal Kelly's FPGA to make the lm96570 of the TX_SDK_V1 firing signal?Or the GUI (TI...
View ArticleForum Post: RE: TI Ultradsound Transmit Solutions\ Opal Kelly \ TX_SDK_V1
Hi, Welcome to TI E2E forum. I have moved your post from the Medical Forum to the Imaging AFEs forum where the LM96570 is supported. I'm sure you'll find an answer here.
View ArticleForum Post: RE: TI Ultradsound Transmit Solutions\ Opal Kelly \ TX_SDK_V1
Hello, No programming is needed to use the GUI with the Opal Kelly board to control the EVM. Regards, Hooman
View ArticleForum Post: RE: TLV990: Minimum Input ADCCLK frequency
Toshi-san, I'm moving this post to the Imaging AFEs Forum. I'm not absolutely certain that this post belongs here, but this forum is the only place where TLV990 questions have appeared. There is a...
View ArticleForum Post: RE: TLV990: Minimum Input ADCCLK frequency
Hi Toshi-san, I’m not familiar with the device itself, so what I can answer is based entirely on the PDS. From the data sheet I see only MAX spec for both the ADC clock and serial interface clock....
View ArticleForum Post: RE: Using LM98725
Hello Hooman, I'm waiting for your response. H ere is my circuit schematic for the circuit.
View ArticleForum Post: RE: Using LM98725
Hi Martin, I'm asking other colleagues to help me answer your questions and I've been promised to get their time by this Friday July 1. Sorry about the delay. Regards, Hooman
View ArticleForum Post: TLV990-13: specifications
Hi all, Could you please share the data of following specifications? 1. About INL and DNL, will the linearity is changed by the value of the PGA? 2. About CDS full-scale input span, is it range of a...
View ArticleForum Post: VSP5610 Application schematic
Hi Can you share the application schematic for VSP5610 between FPGA & CCD Camera/ REgards Aji
View ArticleForum Post: RE: VSP5610 Application schematic
(Please visit the site to view this file)Aji, See the attached Application circuit. Regards, Kurt
View ArticleForum Post: RE: TLV990-13: specifications
Toshi, Thank you for your patience while we see what we can find for you.
View ArticleForum Post: RE: TLV990-13: specifications
Here is what I was given from the team: Linearity does not change as a function of PGA. However ADC output will be noisier as PGA gain increases: because at high gain any noise at the analog input will...
View ArticleForum Post: Ultrasound Analog Front End With 204B interface
Dear Sir, Do you have Ultrasound Analog Front End With 204B interface product?
View Article