Forum Post: RE: VSP5610: VSP5640 CCD AFE no information on TI.com
Closing the thread since the discussion has been taken offline.
View ArticleForum Post: VSP5610: whether VSP5640 interface compatible with VSP561X
Part Number: VSP5610 Dear all, i want to know whether VSP5640's LVDS interface compatible with VSP561X? thanks a lot.
View ArticleForum Post: RE: VSP5610: whether VSP5640 interface compatible with VSP561X
Hi ZYT, I would like to take this conversation offline. Please send an email to praveen.aroul@ti.com
View ArticleForum Post: LM98725: Part Obsolescence
Part Number: LM98725 Proposal to use the LM98725 in one of our new spectrometers. Can we count on this part being available for another 10 years?
View ArticleForum Post: RE: LM98725: Part Obsolescence
Hi Lief, Please contact sales or your disty for this information. These forums are geared towards technical support. Thanks, Aaron
View ArticleForum Post: VSP5610: RGB control timing in VSP5640
Part Number: VSP5610 Hi team, I have question about VSP5640. in each TR cycle, I know how to control LED statues, turn on or off, like below But for three TR cycle, how control RGB three LEDs? how to...
View ArticleForum Post: RE: VSP5610: RGB control timing in VSP5640
additional question: if the T = (LEDn TG T15+1 ) * Tmclk > 1 line cycle , does the LEDn_TG have any output ? or the LEDn_TG cleared by the next LS?
View ArticleForum Post: RE: VSP5610: RGB control timing in VSP5640
Hi Betty, Kevin, I am not sure what you mean by TR cycle. I am assuming you are referring to the Line cycle time LS. Please refer to section 12.3 for the correct sequence to follow to enable the LED...
View ArticleForum Post: LM98714: Do we have the LM98714 P2P solution or Roadmap?
Part Number: LM98714 Hi team, Do we have the LM98714 p2p solution or roadmap? Thanks!
View ArticleForum Post: RE: LM98714: Do we have the LM98714 P2P solution or Roadmap?
Hi, I have notified the expert regarding this issue. Pl expect a response by 8/24/18. Thanks, Aaron
View ArticleForum Post: RE: LM98714: Do we have the LM98714 P2P solution or Roadmap?
Hi, We don't have a p2p solution but we have the next generation part- LM98725 with additional features. This part can be a good replacement for LM98714 Regards, Costin
View ArticleForum Post: LM98640CVAL: DLL False lock & serial interface problems
Part Number: LM98640CVAL Hi, I recently purchased the LM98640CVAL evaluation board, and I have been having trouble communicating with the analog front-end (AFE) via the serial interface. In most cases,...
View ArticleForum Post: RE: LM98640CVAL: DLL False lock & serial interface problems
Hi Bradley, Can you please confirm the power supplies you have provided to the CVAL EVM. You state putting +5V on JR4 which is confusing to me since this is labeled -5V on the schematic. Did you mean...
View ArticleForum Post: RE: LM98640CVAL: DLL False lock & serial interface problems
Hi Bradley, Thanks for the feedback. The datasheet lists the min SCLK frequency as 1 MHz, because that was how the part tested and qualified. We have found that the part will function properly with...
View ArticleForum Post: RE: LM98640CVAL: DLL False lock & serial interface problems
@Christian Yes, sorry. JR1 is correct. I misread the schematic as I was typing my post. Before powering the rest of the board, I checked that I was getting the correct voltages on pin 5 of both JP6 and...
View ArticleForum Post: RE: LM98640CVAL: DLL False lock & serial interface problems
Bradley, I will send you a set up instructions for doing test pattern mode. You could try this and if it works, work backwards from there for your set up.
View ArticleForum Post: RE: LM98640CVAL: DLL False lock & serial interface problems
Kriby and Christian, Sorry for the delay; I meant to write you yesterday. I am fairly certain I have identified the problem. I found that my FPGA development board was sending additional, erroneous...
View ArticleForum Post: RE: LM98640CVAL: DLL False lock & serial interface problems
Thanks for the update and I am glad you were able to figure out your problems. As far as the registers go, the status bits will either can not be written or will self reset. Some of the reserved bits...
View ArticleForum Post: RE: ADC34J45EVM: config file issue
Hi, Are there FPGA example design or documents for ADC34j45EVM ? Best, Hong
View ArticleForum Post: ADS1293EVM: ADS1293EVM: Problems with demo ADS1293EVM installing...
Part Number: ADS1293EVM When following the instructions to install the software for the ADS1293EVM from And following the installation instructions the MSP430 driver update fails. The error message is...
View Article