Forum Post: RE: ADS1263EVM-PDK: MMB0
Hi LH, The ADCPro installer doesn't include this driver. It is only provided in the Plugin installer. The Plugin installer can be downloaded from here: http://www.ti.com/tool/ads1262evm-pdk Best...
View ArticleForum Post: RE: ADS124S08: Configuring for a single-ended measurement
Jens, Ok, I didn't realize that you had wired the AINCOM up. However, I'm a bit stumped. The circuit looks like it should work and I don't see anything wrong with the register settings for making the...
View ArticleForum Post: RE: ADS1263EVM-PDK: MMB0
Again, This package, ADS1262EVM-PDK , does not include driver for MMB0 board. PC shows an "Unknown" device.
View ArticleForum Post: RE: ADC128S102: What is the number of transistor of thaT device?
Hello, Please see the FAQ thread below: e2e.ti.com/.../716168
View ArticleForum Post: ADS1234: Ads1234
Part Number: ADS1234 We are using ads1234 for measuring load cell value. Load cell is 1mV/V and excitation voltage is 5V. Our issue is that the ads1234 output is non-linear at gains of 64 and 128....
View ArticleForum Post: ADS114S08: Calibration Timing
Part Number: ADS114S08 Hi support team, What is the formula for calculating the calibration time of ADS114S08 ? How is the relationship between Calibration Time vs Data Rate? These are not mentioned in...
View ArticleForum Post: RE: ADS5263: FPGA LVDS interface
Hi Chen, Thank you for this answer. We use an Intel CycloneV GX (5CGXFC9E6F35C7) FPGA which doesn't seem to have DPA (Digitla Phase Alignment circuitry). I have already implemented capture scheme using...
View ArticleForum Post: RE: ADC3224: ADC usage in syncronous sampling
Hi Timo, I have contacted the design team in order get the information you have requested. Thank you for your patience! Best Regards, Dan
View ArticleForum Post: RE: ADS1118: Holding Last reading
I have attached two files, one is the schematic showing all parts for the analog input, the other is the schematic showing the parts that are not placed or value changes that are used for the device....
View ArticleForum Post: RE: DAC5652A: Question about IOUTFS
Hi Naoki-san, Yes, disconnecting the RSET should work. The customer can also try to put the DAC in sleep mode and turnoff the clock signal to DAC and also turn off the data going into the DAC. Regards,...
View ArticleForum Post: RE: AFE4300: AFE4300
Hello i need to use the VLD0 as interneal extation for the load cells how can i initiliaze the VLD0 to use it ? where is that in the AFE4300 ? how can i initialize that and where is that in the AFE4300...
View ArticleForum Post: RE: AFE4300: AFE4300
Hello i need to use the VLD0 as interneal extation for the load cells how can i initiliaze the VLD0 to use it ? where is that in the AFE4300 ? how can i initialize that and where is that in the AFE4300...
View ArticleForum Post: RE: ADC12J4000EVM: Sample Mapping and Ordering
Hi Jim, Would it be possible to supply an inclusive SDK build for the Vivado reference design to eliminate any uncertainty regarding the HW configuration. I believe I have the correct configuration...
View ArticleForum Post: RE: DAC8760: Analog output multiplexing with DAC8760
Hi Alessio, I am not sure what happened but your previous reply is blank. Can you re-post your reply? Thanks, Garrett
View ArticleForum Post: DAC38RF87: Operating Parameters of this and the other DACs in...
Part Number: DAC38RF87 All, There is a little confusion in the datasheets of this particular family of DACs, so I have several technical questions in relation to really all of them: Are the DACs able...
View ArticleForum Post: RE: ADS1298RECGFE-PDK: ADS1298R EVM Evaluation software stuck in...
Hi Elvar, Thank you for your post and welcome to our forum! What you are seeing generally happens when the host DSP on the MMB0 cannot communicate with the ADC on the ADS1298RECGFE board. Can you probe...
View ArticleForum Post: RE: ADS124S08: Configuring for a single-ended measurement
Thanks Bob and Joseph. I nailed it now! The problem was that my code was toggling between the RTD readings and reading the Thermistor. Once I measured on REFOUT I could see it turning on/off. The...
View ArticleForum Post: RE: DAC161S997: DAC Output Problem
Hello, Is the GND of the supply shorted to Loop- as you have drawn? Have you tried connecting a single load resistor between the supply GND and Loop-? What is the purpose of the zener diode? Thanks,...
View ArticleForum Post: RE: DAC161P997: Error reporting issues
Hi Garrett, The ERRLVL pin is at 0 and the error current is the default ERR_LOW, 3.375mA. I see this error current frequently when I have error reporting enabled, and the threshold set to 0. However, I...
View ArticleForum Post: RE: ADS1262: .
Hi, Welcome to the TI E2E Forums! The ADS1262 is intended for low-frequency measurements, generally less than several kHz, as the digital filter attenuation increases significantly for higher...
View Article