Forum Post: RE: ADS1262: ads1262
hello sir, as you say is it write?? i get speed but i can't get stable output CS_=0; x3 = read(0x12); // CS_=1; for (i1 = 0; i1 < 10; i1++) { CS_=0; x1 = read(0x00); //display on screen CS_=1;...
View ArticleForum Post: RE: DAC5652A: Clock signal accept after SLEEP mode
Naoki, Please attached photo of a screen shot of the test results. The scope was set to 20us/div. On the photo you will see the clock, the DAC output and the sleep signal. Regards, Jim
View ArticleForum Post: RE: DAC5652A: Clock signal accept after SLEEP mode
Naoki, One thing I forgot to point out is the clock shown in the photo is actually an inverted version of the clock going to the DAC. Regards, Jim
View ArticleForum Post: RE: ADC32RF44: Code error rate.
William, We are looking into this. Regards, Jim
View ArticleForum Post: RE: ADS42LB69: Some question about ADS42LB69
Jerry, We are looking into this. Regards, Jim
View ArticleForum Post: RE: ADS130E08: Sample C code and password for zip
Hi Eduardo, The example code for the ADS130E08 that you are referring to used to be stored on a public FTP site, unfortunately we had to shut down the site for security reasons. The archive is too...
View ArticleForum Post: RE: ADS42LB69: Some question about ADS42LB69
Jerry, There are ESD protection diodes from ground-to-pin and pin-to-supply at each INP and INM pin. Also you can power down either CHA or CHB and use the channel that is on in DDR mode. This is a typo...
View ArticleForum Post: RE: ADS1231: Do we have example C code for ADS1231?
The ads1x31ref_fwsrc_1.0.0.zip is the firmware source for the Eval board. FWSRC -> FirmWareSouRCe. Please reference your own TI staff remarks in the original thread. Bob Benjamin: " As this device...
View ArticleForum Post: RE: ADS1262: ads1262
Hi Kinnari, Keep the /CS signal held low for the entire command, as shown in the image above. If you toggle /CS in the for-loop it will terminate the current read data command and the output data won't...
View ArticleForum Post: ADS1298: ADS1298 stop working when Bluetooth module starts
Part Number: ADS1298 Dear Ti rep, We have demonstrated beyond any shadow of a doubt that permanent aka static magnetic fields has no discernable effect on ecg signals especially using the ads 1293. My...
View ArticleForum Post: RE: ADS1231: Do we have example C code for ADS1231?
Hi Richard, Unfortunately due to situations beyond our applications team control the firmware zip is no longer available for distribution in the current form. This firmware is actually very old and...
View ArticleForum Post: ADS7253: SPI interface Question
Part Number: ADS7253 Hi TI Team I am using ADS7253IRTER chip for measuring the analog voltage. I want to use internal reference voltage for the ADC. Could you please tell me the steps for configuring...
View ArticleForum Post: RE: DAC161S997EVM: got the following error message when starting...
Garrett, I got the same error message even NI is installed and power is connected, please find my setup below: Can you please advise back, thanks in advance. Best regards, Shai
View ArticleForum Post: AMC1304M05-Q1: Discontinuous current sensing and Common mode voltage
Part Number: AMC1304M05-Q1 I intend to use the AMC1304 sigma delta modulator for inductor current sensing in a dual interleaved boost converter that am designing. This boost converter will have an...
View ArticleForum Post: RE: ADS7253: SPI interface Question
Hi Chandan, The register details for the ADS7523 you described look fine to me. One thing to keep in mind is that you need 48 SCLK cycles to write or read the various registers. When you are simply...
View ArticleForum Post: RE: AMC1304M05-Q1: Discontinuous current sensing and Common mode...
Hi Paul, Welcome to our e2e Forum! We have had other customers use the AMC1304 in similar applications, so the quick answer to both of your questions is 'yes'. Regarding the input common mode voltage,...
View ArticleForum Post: RE: AMC1304M05-Q1: Discontinuous current sensing and Common mode...
Asante sana (thank you in swahili)
View ArticleForum Post: ADS7881: Driving ADS7881 by high-speed optocouplers
Part Number: ADS7881 Hi, Since isolation of 2500Vrms is needed between the digital module and the analog module , we use high-speed optocouplers - ACSL-6400. The optocoupler drive the A/D Digital...
View ArticleForum Post: DAC121C085: DAC121C085 Example code
Part Number: DAC121C085 Hi, I am trying to use DAC121C085 with msp432p401R and i need an example code. Is there an example code ? Thank you.
View ArticleForum Post: RE: ADS1298: ADS1298 stop working when Bluetooth module starts
Hi Dr. Muh, Can you please try to re-attach your image? It does not appear to have come across with your post.
View Article