Forum Post: RE: AFE5805 or LM96511
Valeri, For the TX810, I can recommend the TPS79633DCQR. Thanks, Chuck Smyth
View ArticleForum Post: RE: AFE5808EVM GUI for Windows 7
I have found the solution. We can basically let windows do the work for us. To install CDM drivers for an FTDI device under Windows 7, follow the instructions below: If no suitable driver is...
View ArticleForum Post: RE: AFE0064 linearity
Hi, I managed to have the linearity up to full scale increasing the delay SHR to SHS up to 100us, then it works fine. unfortunately I cannot reduce V1 due to the interface to the ADC. I hope that will...
View ArticleForum Post: RE: TWS1250EVM & AFE5805EVM - parallel data on header
Gunter, The data is simultaneously doing both. You can send two channels to the CMOS output headers. At the same time, you can capture one channel in the FIFO to send to the PC. This should work for...
View ArticleForum Post: RE: question about AFE5805 schematic
Lutao, I understand your frustration because that confuses me as well. In ramp mode, all channels are outputting a ramp signal and in normal mode you probably have connected only one input and...
View ArticleForum Post: VSP01M01 / VSP01M02 and VSP2590 Minimum conversion rates
We are looking at replacing an obsolete AFE / TG device in an existing product with either the VSP01M01 / 02 or the VSP2590. This product runs in a fast mode and a low noise mode. Convert rates for...
View ArticleForum Post: RE: AFE5808
Matt, The phase generator is meant for better alignment of all eight channels into the summing amplifier. The user can control the phase delay of each of eight channels individually through SPI...
View ArticleForum Post: RE: AFE5851 EVM & SP605
Rino, Yes I can see why say it is not ideal. All of the newer AFEs like AFE5808A have the Samtec connector on the top instead of the bottom which makes it easier to mate with the TSW1250 and probably...
View ArticleForum Post: RE: LM96511 EVM
Hi Chuck I'm back! I didn't make a Bytes/bit error. I missed a '0' while reviewing my numbers this morning! Can I confirm your last comment: > 40MSPS sampling, 5MHz RF input, 1kHz rep rate and...
View ArticleForum Post: Pulse Patterns from TX-SDK-V2
Hello again, What are the pulse patterns available from the TX-SDK-V2? Most importantly what is the time between pulses? (Is there any way I can see the documents that come with the TX-SDK-V2? There is...
View ArticleForum Post: RE: AFE5808 output-referred noise
Damian, The ORN includes the ADC noise. Thanks, Chuck
View ArticleForum Post: RE: TSW 1250evm + AFE 5851
Hi Allen, I write directly to your email address, because I have the same problem of Eric. I need to acquire multi-channel data simultaneously. Thanks, Rino
View ArticleForum Post: RE: AFE5851 EVM & SP605
Rino, Yes, I talked with Richard today. I don't have experience with this matlab code, so it would be difficult to modify the matlab code to work with the TSW1250. That is unless it ports easily as...
View ArticleForum Post: RE: AFE5808 SPI Programming
Paul, The main SPI signals are SEN, SDATA and SCLK. These are the only signals required to write to the registers. Additionally, PDN_FAST_VCA, PDN_FAST_ADC, and PDN_GLOBAL are also USB signals that...
View ArticleForum Post: RE: Pulse Patterns from TX-SDK-V2
Gunter, I can an answer on this by Friday. Let me see if I can get those documents. Thanks, Chuck Smyth
View ArticleForum Post: RE: AFE5851 EVM & SP605
Hi Chuck, I don't have a great experience with that kind of matlab code, so I could only try to see what can I do. The problem is that I have just two week to do something work. We'll see. Thanks a...
View ArticleForum Post: RE: TSW 1250evm + AFE 5851
Good mornig Allen, are there the possibility of supplying multi-channel data simultaneously with TSW1250? I see that the last post is on april, so I'd like to know if there are something new. Thanks, Rino
View ArticleForum Post: RE: Pulse Patterns from TX-SDK-V2
Gunter, TX734 is not available. We have the TX517 but that is only 1-2 channels. LM96550 is the only 8-channel pulser available. What TX-SDK-V2 documents would you like to see?
View ArticleForum Post: RE: AFE5851 EVM & SP605
Hi Chuck,I was able to acquire with the TSW1250 using the MATLAB code. Now my problem is to acquire the external trigger from the same MATLAB code.Could you help me? Do you know anyone who could help...
View Article