Forum Post: RE: TX-SDK-V2 EVM Power problem at banana connector cable
Hi Subash, I just replied to your other post on this as well: e2e.ti.com/.../2001138 Regards, Hooman
View ArticleForum Post: RE: TX-SDK-V2 EVM has problem
Hi Hooman, Yes, We followed the power sequencing as per data sheets. When we started to work with this board, initially we faced problem in the link e2e.ti.com/.../542675 then next day we have seen the...
View ArticleForum Post: RE: TX-SDK-V2 EVM has problem
Hi Subash, Could you please contact me with email: hooman.hashemi@ti.com Regards, Hooman
View ArticleForum Post: AFE 5818 ADC SNR value of 14 and 12 bit
In AFE5818 EVM, 12 bit and 14 bit ADCs are there. For 12 bit ADC, the SNR is given in datasheet as 72dB. For 14bit ADC, the SNR is given in datasheet as 75dB. To calculate the SNR, the formula is...
View ArticleForum Post: RE: Using LM98725
Here is the schematic of my PCB circuit, I have configured the registers but still didn't get any output frequency from the chip can you please where the problem could be? I need 5MHz output clock from...
View ArticleForum Post: RE: Ultrasound Imaging using 40-100KHz transducer array
Try using ultrasound IC from microchip for your pulsar/transmission and for receiver AFE5809 should work.
View ArticleForum Post: RE: Using LM98725
Hi Martin, Sorry, I could not follow the register write sequence that you've shown. Can you put the register map into a text format so that it's clear what the register content (Hex value) are?...
View ArticleForum Post: AFE58xx Vin hi and low
In the AFE58xx data sheets the Vin for hi is specified from 2V to 3.3V. Is this correct, since DVDD is 1.8V. Can the SPI port on the AFE58xx be driven by 1.8V IO from a FPGA?
View ArticleForum Post: RE: Using LM98725
Hi Martin, I cannot figure out what could be causing your issue. I'd have to defer the next level of response to my colleague who'd be back in office on Monday Oct. 24. I'd discuss with him and get...
View ArticleForum Post: The difference between LM96570 demo kit TX-SDK-V1 and TX-SDK-V2
Hi, My customer would like to evaluate LM96570 , and would like to purchase the demo kit. They have below question that urgently need TI to feedback. What is the difference between below 2 demo kits of...
View ArticleForum Post: TX_SDK_V1 ultrasound Tx Evaluation kit broken?
Dear technician, We bought a TX_SDK_V1 on April 18, 2016. Yesterday, we first plugged in the power supplies and started testing. However, we failed to apply some of the power supplies in sequence as...
View ArticleForum Post: AFE5803EVM installation
Hello, Is it possible to install the AFE5803EVM GUI on Windows 10? I installed, restarted, and launched the GUI, and I got the following error message: Thanks for your help. Paul Hultz
View ArticleForum Post: RE: The difference between LM96570 demo kit TX-SDK-V1 and TX-SDK-V2
Hi Sam, This E2E thread answers your question about the differences between the TX-SDK-V1 , and the TX-SDK-V2 : Please note that some of the devices used on this EVM (demo kit) may be hard to procure...
View ArticleForum Post: RE: Using LM98725
Hello Hooman, In the datasheet on page 87, Figure 66 & 67 shows that the SDI pin is receiving the data commands before the 9th clock but in the description its written that master will take control...
View ArticleForum Post: RE: Using LM98725
Dear Hooman, I have read the datasheet again and its written that the master clock source for the CIS sensor will work Crystal Oscillator Mode but in my case I'm not using crystal oscillator. I'm...
View ArticleForum Post: RE: Using LM98725
This is the clock signal I'm getting from the chipm. Blue one is the INCLK 3MHz and Yellow is PHIA1
View Article