Forum Post: RE: ADS1299: Can not get full range readings even if my leads are...
Hi Yf, Thanks for your post! As per table 9, 7FFFFFh is the max code while 800000h is the minimum code. Is 2500000 in decimal? Are you using the internal test signal to generate this value as your...
View ArticleForum Post: RE: DAC3482EVM: Phase noise out of DAC higher then DAC CLK Phase...
Kang, Again thank you for the quick reply. The app note you sent are very interesting and may be useful as we move farther in the design but they do not answer my question. We are doing all our...
View ArticleForum Post: RE: ADS1299: Ads1299 read data 4 time the same
Hi Stefan, Yes, I mean to just read 1 channel at a time with SPI. You will have to change your code.
View ArticleForum Post: RE: TSW3085EVM: DAC3482 on TSW3085EVM does NOT seem to work
Hi Terry, you may download the CPLD files for the TSW308x family below: (Please visit the site to view this file)
View ArticleForum Post: RE: ADS7828: latch-up, reports wrong conversion value
Sandeep, Here's a piece of the schematic showing the ADS7828 . (Please visit the site to view this file)
View ArticleForum Post: RE: DAC3482EVM: Phase noise out of DAC higher then DAC CLK Phase...
Hi Thomas, I expect to observe the same trend. Based on all the previous testing, this is the case. I do not expect the step response like you have in your data for the DAC3482 . This is the reason I...
View ArticleForum Post: RE: ADS1299: Ads1299 read data 4 time the same
Hi Alex Looks first time bether... If I read Channel 1 => Channel 1 is ok ! If I read Channel 1 + Channel 2 => Channel 1 is ok Channel 2 is ok If I read Channel 1 + Channel 2 + Channel 3 =>...
View ArticleForum Post: RE: ADC12DJ3200EVM: The Procedure of Settings
Hi Toshi The LMK04828 is only used in distribution mode. The RFoutB output at 1406.25 MHz from the LMX2582 is input to the LMK04828 . The LMK04828 just divides this down to create the needed CLK and...
View ArticleForum Post: DAC8760EVM: DAC 8760 EVM Software - LabView Run time engine
Part Number: DAC8760EVM Hi, After installation, when I try to run the program (on W7 64bit) I have the following error: "Unable to locate the Labview Run Time Engine" I tried to install the Engine...
View ArticleForum Post: RE: ADS4225: Output impedance of DA[0..11] and DB[0..11] when...
Hi User5059038, We are looking into your question and will get back to you soon. Regards, Neeraj
View ArticleForum Post: ADS1261: SINC4
Part Number: ADS1261 Hi Sir May I know TI have SINC4 document to explain the detail ? I saw TI have ADS1261 / ADS124S08 24bit ,beside channel is different May I know what's the key different between...
View ArticleForum Post: ADS1299: Frequency vs Gain characteristics
Part Number: ADS1299 Hi, I was requested Frequency vs Amplitude characteristics of ADS1299 with 1000/2000/4000 SPS from my customer. Do you have such data? (What is required such data is first time for...
View ArticleForum Post: ADS122C04: TIDCEE5 Software download broken package
Part Number: ADS122C04 Hi, I´ve tried to download the High Precision Temperature Measurement for Heat and Cold Meters Reference Design software package under: But the containing .zip isn`t complete and...
View ArticleForum Post: RE: DAC9881: Is there any unbufferd voltage for the DAC9881 series?
Hello Kevin, Here is our experiment results, we just record VOUT form ideal 0 V to 0.4 V. ( since the measure time is too long if VOUT go up to its VREF ) Through its raw data we try to count the DNL...
View ArticleForum Post: RE: DAC161S997: DAC Output Problem
Normally 24V will be connected to a dc/dc converter so i can use it but for now i was just using exp-msp432p4111 board which gets power from usb and an other PCB for DAC which i shared its schematic...
View ArticleForum Post: RE: DAC161S997: Problem With two DAC161S997's in two wire loop...
Thanks Garrett for giving your valuable time for us...!!!
View ArticleForum Post: RE: ADS1298: ADS1298 SPI not Reading
A step in the right direction Daniel! Let me know if you have further questions here, code to voltage conversion is probably next which is covered in this thread: e2e.ti.com/.../1363393 If you have...
View ArticleForum Post: RE: Linux/ADS1299: The value of the CH1 data is different
Keunsoo, Are you converting the code to voltage correctly as I indicated in the previous post?
View ArticleForum Post: RE: ADS1299: Frequency vs Gain characteristics
Hello Kuramochi-san, To clarify, is your customer looking for FFT plots like Figure 13. in the datasheet?
View ArticleForum Post: RE: TSW14J10EVM: Is there support for ADS52J90EVM in HSDC Pro?
Hi Praveen, Any good news from the software team? Thanks, Eu Hong
View Article