Forum Post: ADS54J60: ADS54J60 page 28 DDC block example query
Part Number: ADS54J60 HI, ADS54J60 is 1GSPS,16 bit and ADS54J42 is 625MSPS, 14 bit Sampling rate ADC. The example shows in ADS54J60 datasheet page no.28, Figure 60, DDC Block has data rates for 625MSPS...
View ArticleForum Post: RE: Compiler/ADS1299: ADS1299
Hello, thank you for the reply. I wrote the following code for mbed compiler and it is quite understandable. ____________________________________________________________ #include "mbed.h" #define F...
View ArticleForum Post: RE: ADS7049-Q1: DVDD in over the recommended max of 3.6V
Hi Sawamoto-san, As noted on page 13, AVDD is used as the reference for the ADS7049-Q1 . Having a stable reference is critical for getting good conversion results from any ADC (see Figure 35 and Table...
View ArticleForum Post: RE: ADC128S102: SCLK and CS_n timing parameters
Hi Chris, Welcome to our e2e Forum! You have a great question here on the ADC128S102 ! The second paragraph under the Programming (continued) section on page 17 explains the differences in tCSS and...
View ArticleForum Post: RE: ADS1294: IEC60601-1, IEC60601-2-27 and IEC60601-2-51 compliance?
Hi Gregory, The ADS1294 does not claim to be compliant to the various IEC60601 standards. Patient protection is part of a system level design, and we certainly do support systems needing to meet the...
View ArticleForum Post: RE: ADS1218: Query regarding the External clock
Hi Makesh, This is normal behavior for the ADS1218 in that after the last SCLK the output of DOUT changes to a high impedance state and is no longer driven. This is indicated in the Timing...
View ArticleForum Post: RE: ADS54J60: ADS54J60 page 28 DDC block example query
Purna, This is a typo in the data sheet. The sample rate should be 1Gsps. Regards, Jim
View ArticleForum Post: RE: ADS8661: ADS8661 Application Note
Hi Jens-Michael! Thank you for your insightful comments! We'll take this into consideration for future generation devices.
View ArticleForum Post: RE: AFE58JD28: fs/2 spur
Hi James, For AFE58JD28 (16 channel AFE) another question related to the offset_CH1: Here is the explanation from our group system engineer: ========== If datrasheet said can’t remove odd and even...
View ArticleForum Post: ADS1298R: DRDY signal ceases to generate
Part Number: ADS1298R Hello, I am having problem getting data out of my ADS1298 , after configuring it in RDATAC mode. All my SPI routines are verified for reading and writing registers. I have carried...
View ArticleForum Post: RE: AFE4300EVM-PDK: problem connecting
Hello Marc, Since we haven't heard back from you, I am assuming you were able to resolve your issue. I am closing this post. If you have any follow-up questions, just post a reply below (or create a...
View ArticleForum Post: ADS9224REVM-PDK: Understanding the ADS9224REVM-PDK display
Part Number: ADS9224REVM-PDK Hi, I am not quite sure how to interperate the ADS9224REVM-PDK spectrum output? how come with both inputs tied to ground we get -10dbC noise floor but with a signal...
View ArticleForum Post: RE: AFE58JD28: fs/2 spur
Hi James, How are you? That means since AFE58JD28 has only 16bit input channels, offset odd and even are the same (identical), therefore in these two registers there is no different. When the device...
View ArticleForum Post: RE: ADS9224REVM-PDK: Understanding the ADS9224REVM-PDK display
I am also unable to find the thermal footprint, the mechincal drawings are missing this information? Mechnical note 4 says "see separate sheet for thermal pad details", there is no other sheet I can see?
View ArticleForum Post: RE: Compiler/ADS1298: ADS1298
Sir, I have been go through of this software but little bit confused about usages of this software. 1. how i used this software with arduino uno board and how get output on serial monitor of arduino...
View ArticleForum Post: Linux/DDC2256AEVM: ddc2256
Part Number: DDC2256AEVM Tool/software: Linux Hi, Could you send me the reference design with DDC2256A EVM based on Intel Altera FPGA Cyclone 4 FPGA with GUI on PC? Thanks and best regards, Bugra
View ArticleForum Post: RE: ADS1298R: DRDY signal ceases to generate
Hi Ninad, Welcome to our e2e forum! As noted in the original post on the ADS1298 , are you reading out the data between DRDY pulses, ensuring that your SCLK is fast enough to retrieve all of the...
View ArticleForum Post: RE: ADS54J42: ADS54J42 temperature issue
We have not heard a response in a bit. I am temporarily closing the post but if there is still an issue please respond with the requested information above and we will address. Thanks, RJH
View ArticleForum Post: ADC121C021: information regarding malfunction of sensing circuit...
Part Number: ADC121C021 I am using ADC121C021 which uses the I2C protocol for transferring the digital data. I am using eight of them to measure eight capacitor voltages in a power electronics circuit....
View ArticleForum Post: RE: ADS1298R: DRDY signal ceases to generate
(Please visit the site to view this file)Here I have attached the schematic file of the board. I have ensured that my SCLK is fast enough to not mess up the DRDY timing, DRDY is 500SPS and SCLK is fast...
View Article